NVIDIA H200 NVL 141GB AIO Liquid Cooler, 360 mm | Astralcooler AC-GBAIO-NVH200

Astralcooler · AC-GBAIO-NVH200

360 mm liquid cooling for the NVIDIA H200 NVL

The Astralcooler AC-GBAIO-NVH200 is a single-card, all-in-one liquid cooler for the NVIDIA H200 NVL 141 GB PCIe GPU. It replaces the stock passive heatsink with a full-cover copper block that draws heat from the GPU, memory, and power components. An inline pump moves coolant to a 360 mm radiator, where three fans remove the heat.

Fits
H200 NVL 141 GB PCIe
Radiator
360 mm
Cold plate
Copper
Pump
Inline

Compatibility

  • ✓NVIDIA H200 NVL Tensor Core GPU, 141 GB HBM3e, PCIe, with the PCB layout shown in the mounting guide

H200 SXM shares the 141 GB capacity and uses a separate module form factor.

Before ordering, match your PCB layout to the diagram in the product gallery and check the screw positions against the mounting diagram below.

NVIDIA H200 NVL PCIe card with its stock heatsink. Photo from Lenovo.

Design Highlights

A copper plate for the GPU and memory

The 157 mm copper plate spans the main heat-producing areas of the PCB. The block routes coolant through up to 176 grooved microchannels.

A separate radiator for the GPU

An inline pump with a ceramic shaft sleeve circulates coolant through braided EPDM tubing. The three radiator fans move air through the aluminum core.

Key Specifications

ModelAC-GBAIO-NVH200
ConfigurationSingle-GPU AIO with backplate
GPU block dimensions266 × 97 × 16.8 mm (L × H × T)
Cold plateCopper, 157 mm long
Radiator360 mm class, aluminum
Radiator with fans399 mm long × 60 mm thick
TubingBraided EPDM
Fan speed3,000 RPM ±10%
Fan static pressure5.3 mm H₂O
Fan airflow99.5 CFM
Fan noise41 dB(A), manufacturer specification
Thermal pads1.5 mm

Astralcooler single-card assembly drawing. Dimensions are in millimeters.

Which Version Do I Need?

Choose an AIO for a dedicated GPU loop or a standalone block if you are building a custom loop.

Astralcooler 360 mm AIOTHIS PAGE
Choose this single-card 360 mm kit for a dedicated setup with its own inline pump and radiator.
Choose the standalone Astralcooler block with backplate if you already have or plan to build your own coolant loop.
Compare this Bykski 360 mm AIO if you want another dedicated loop. Check its radiator clearance and board diagram against your build.
For a custom loop, compare your PCB with the board photo on the N-H200-SR-QH product page. Choose this vacuum-brazed block with backplate only if your PCB matches.

What's in the Box

1 single-GPU AIO assembly with block, 360 mm radiator, inline pump, and tubing3 radiator fans1 GPU backplate1.5 mm thermal padsM2 × 7 mm spring screwsM2 × 8 mm backplate screws

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Power down and disconnect the system. Remove the GPU and its stock heatsink, then clean off the old thermal interface material.
2
Place the 1.5 mm pads as shown and apply your own GPU thermal paste to the GPU die.
3
Align the water block and backplate with the PCB. Use the spring screws and backplate screws shown in the mounting diagram.
4
Mount the radiator in a 360 mm position with room for the 399 mm length and 60 mm stack. Route the tubing without kinks. Follow the pump, fan, and system documentation when connecting power.
5
Check the coolant connections for leaks. Verify pump and fan operation before putting the GPU under load.

You will also need your own GPU thermal paste, the tools for your card's stock cooler, and a chassis with clearance for the radiator and tubing.

1 Water block · 2 Thermal pads · 3 GPU board · 4 Spring screws · 5 Backplate · 6 Backplate screws

FAQ

How is the H200 NVL cooled from the factory?

The stock full-height, dual-slot H200 NVL PCIe card uses a passive heatsink and relies on chassis airflow. The AIO replaces that heatsink and moves GPU heat to a fan-cooled radiator.

Do I need to buy a separate pump and radiator?

This AIO includes the inline pump, tubing, radiator, and fans.

What case clearance does the cooler need?

Start with a 360 mm radiator mount and check for 399 mm of length and 60 mm of thickness with the fans in place. Allow extra room for the hoses to turn toward the card.

Does 141 GB identify the right board?

Check the complete model name and the PCB. NVIDIA lists 141 GB for both the H200 NVL PCIe card and the H200 SXM module.

Notes
  • The 480 mm callout shows the vertical distance from the bottom of the radiator fans to the bottom edge of the GPU block in the drawing.