Barrow · BS-GIG3090-PA2
Water block for select Gigabyte RTX 3080, 3080 Ti and 3090 cards
The Barrow BS-GIG3090-PA2 is a full-cover GPU water block for select Gigabyte graphics cards, including the GeForce RTX 3080 VISION OC 10G (Rev. 1.0 and 2.0). Its copper cold plate transfers heat from the GPU die, memory, and power circuitry to a custom liquid cooling loop.
Fits
Select Gigabyte RTX 3080 / 3080 Ti / 3090
Ports
G1/4 inlet and outlet
Compatibility
Barrow lists these Gigabyte GeForce PCB configurations for the BS-GIG3090-PA2 front block.
- ✓RTX 3080 VISION OC 10G (Rev. 1.0)
- ✓RTX 3080 VISION OC 10G (Rev. 2.0)
- ✓RTX 3080 GAMING OC 10G (Rev. 1.0)
- ✓RTX 3080 GAMING OC 10G (Rev. 2.0)
- ✓RTX 3080 EAGLE OC 10G (Rev. 1.0)
- ✓RTX 3080 EAGLE OC 10G (Rev. 2.0)
- ✓RTX 3080 EAGLE 10G (Rev. 1.0)
- ✓RTX 3080 EAGLE 10G (Rev. 2.0)
- ✓RTX 3080 GAMING OC WATERFORCE WB 10G (Rev. 1.0)
- ✓RTX 3080 Ti GAMING OC 12G
- ✓RTX 3080 Ti VISION OC 12G
- ✓RTX 3080 Ti EAGLE OC 12G
- ✓RTX 3090 GAMING OC 24G
- ✓RTX 3090 EAGLE OC 24G
- ✓RTX 3090 EAGLE 24G
- ✓RTX 3090 VISION OC 24G
- ✓RTX 3090 TURBO 24G
Barrow lists a different block, BS-GIX3090-PA, for the AORUS RTX 3090 MASTER 24G (Rev. 1.0).
Before ordering, verify your exact card model and revision and compare the PCB layout with Barrow’s fit information.
Gigabyte RTX 3080 VISION OC 10G (Rev. 2.0). Check your PCB before ordering.
Design Highlights
Full-cover cold plate
The cold plate draws heat from the GPU die, memory, and power circuitry. The clear acrylic top lets you see the coolant path.
43 microchannels over the GPU
Coolant flows through 0.5 mm grooves in the cold plate over the GPU die.
Loop fittings shown for illustration.
LRC 2.0 addressable lighting
Use a compatible LRC 2.0 manual controller for the lighting. For motherboard control, use a separately sold 5V 3-pin ARGB adapter cable.
Key Specifications
| Block model | BS-GIG3090-PA2 |
|---|
| Cold plate | Copper |
|---|
| Top | Clear acrylic |
|---|
| Cooling coverage | GPU die, memory, and power circuitry |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Block length × width | 304.80 × 138.50 mm |
|---|
| Maximum height shown | 23.90 mm |
|---|
| Lighting | Barrow LRC 2.0, 5V 3-pin ARGB |
|---|
Barrow front-block drawing. Dimensions are in millimeters.
Which Version Do I Need?
Match the name on your card to the block made for its PCB.
Barrow BS-GIG3090-PA2THIS PAGE
Choose this front block for the Gigabyte card and revision listed above.
Choose this block for the NVIDIA GeForce RTX 3090 Founders Edition.
Choose this block for the Gigabyte GeForce RTX 3090 Ti GAMING OC 24G.
What's in the Box
1 × front GPU water block1 × manual lighting controller2 × G1/4 stop plugsMounting hardware setThermal pad set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Turn off the system, remove the graphics card, and take off its original cooler.
2Clean off the old thermal materials. Apply thermal paste to the GPU die and place the thermal pads where the memory and power components meet the block.
3Align the block with the PCB and secure it with the mounting hardware. Check the fit before tightening the screws.
4Check the inlet and outlet positions before connecting your tubing. Use G1/4 fittings and seal any unused ports with the stop plugs.
5Check the completed loop for leaks before powering the graphics card.
For a complete loop, you also need tubing, matching G1/4 fittings, a pump, a reservoir, a radiator with fans, and coolant.
Barrow’s general mounting illustration. Verify the contact points and screw positions on your card.
FAQ
Does this fit my Gigabyte RTX 3080 VISION OC 10G?
Barrow lists both Rev. 1.0 and Rev. 2.0 for this block. Verify your card’s revision and PCB layout before ordering.
Does Barrow list the RTX 3080 Ti EAGLE OC 12G?
Barrow lists the Gigabyte GeForce RTX 3080 Ti EAGLE OC 12G. Check the exact model name on your card.
Can I reuse my card’s original backplate?
Yes. Barrow lists the front block as compatible with the original backplate on a supported card. The active water-cooled backplate is a separate accessory.
How do I connect the lighting to my motherboard?
Use a compatible 5V 3-pin ARGB adapter cable, sold separately, and align it with the header markings. A 12V RGB header can damage the lighting.
What fittings do I need?
Use G1/4 fittings sized for your tubing. The box includes stop plugs for unused ports.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.