Barrow · BS-MSG4090M-PA

Full-cover water block for MSI GeForce RTX 4090

The Barrow BS-MSG4090M-PA replaces the factory cooler on supported MSI GeForce RTX 4090 cards, including the SUPRIM X 24G, for use in a custom liquid cooling loop. Its copper cold plate draws heat from the GPU core, memory, and power delivery components. The included aluminum backplate mounts behind the board.

Fits
Select MSI RTX 4090 24G cards
Cold plate
Copper
Ports
G1/4 inlet and outlet
Lighting
5V LRC 2.0 ARGB

Compatibility

Barrow lists this block for these MSI card models.

  • ✓MSI GeForce RTX 4090 SUPRIM X 24G
  • ✓MSI GeForce RTX 4090 SUPRIM 24G
  • ✓MSI GeForce RTX 4090 SUPRIM LIQUID X 24G
  • ✓MSI GeForce RTX 4090 SUPRIM LIQUID 24G
  • ✓MSI GeForce RTX 4090 GAMING X TRIO 24G
  • ✓MSI GeForce RTX 4090 GAMING TRIO 24G

Barrow specifies a different block for the NVIDIA RTX 4090 Founders Edition. Before ordering, verify your exact card model and PCB layout.

Three of the compatible MSI cards shown in Barrow’s product photos. From left, SUPRIM X 24G, SUPRIM 24G, and GAMING X TRIO 24G.

Design Highlights

Cooling for the core, memory, and VRM

The cold plate covers the GPU core, memory modules, and power delivery components. Coolant carries heat from the plate into the rest of your loop.

43 jet microchannels

The microchannels in the GPU core area give the coolant more surface area to draw heat from the cold plate.

5V addressable lighting

Connect the lighting to a compatible Barrow LRC 2.0 controller. For motherboard sync, use a Barrow adapter cable and a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the LEDs.

Key Specifications

ModelBS-MSG4090M-PA
Block typeFull-cover GPU water block
Cold plateCopper
TopClear acrylic
BackplateAluminum alloy, passive
Port threadG1/4 inlet and outlet
Block size (L × W × max T)254.10 × 151.80 × 24 mm
Lighting5V Barrow LRC 2.0 ARGB

Barrow’s drawing shows dimensions in millimeters, including two thickness measurements taken at different points.

Which Version Do I Need?

Match the block to your exact card model and PCB before choosing.

Barrow BS-MSG4090M-PATHIS PAGE
Choose this clear-top block if your MSI RTX 4090 matches the compatibility list above.
Choose this Barrow model for the NVIDIA GeForce RTX 4090 Founders Edition.
Compare this full-armor option if you have the MSI RTX 4090 GAMING X TRIO 24G and prefer an armored block.

What's in the Box

1 × full-cover GPU water block1 × aluminum alloy backplate2 × G1/4 stop plugsMounting screws and washersThermal pad set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

The backplate mounts behind the graphics card PCB.

Installation & Use

1
Power off the PC, remove the graphics card, and take off the factory cooler. Clean off the old paste and pads.
2
Cut the supplied thermal pads to the shapes shown in Barrow’s guide and place them at the matching contact points. Apply your own thermal paste to the GPU core.
3
Align the block, PCB, and backplate. Check that the block sits flush before securing the screws and washers in their designated positions.
4
Connect your loop to the inlet and outlet with G1/4 fittings and close the unused ports with the stop plugs.
5
Leak-test the loop before powering the graphics card.

For the loop, you also need G1/4 tubing fittings, matching tubing, a pump, a reservoir, a radiator with fans, and coolant.

Barrow’s cold plate pad guide. 1 = 1.2 mm, 2 = 0.5 mm, and 3 = 1.0 mm.

FAQ

Does this water block fit the MSI RTX 4090 SUPRIM X and GAMING X TRIO?

Yes. Barrow lists both the SUPRIM X 24G and the GAMING X TRIO 24G. Match the exact model and PCB before ordering.

Which Barrow block fits the RTX 4090 Founders Edition?

Use the Barrow BS-NVG4090-PA for the NVIDIA GeForce RTX 4090 Founders Edition.

Can I sync the lighting with my motherboard?

Yes, with a compatible sync adapter cable and a 5V 3-pin ARGB header. The standard package does not include a sync adapter cable.

Does the included backplate need its own coolant connection?

The aluminum backplate is passive and mounts behind the PCB. Connect the loop to the water block.

What fittings do I need for the block?

Use G1/4 fittings sized for your tubing. The two included stop plugs close the unused ports.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.