Barrowch · FBRWB-PA4

DDR5 RAM water block with a TFT coolant display

The Barrowch FBRWB-PA4 adds desktop DDR5 memory to a custom liquid cooling loop. It mounts across the RAM cooling armors, which transfer heat from the memory modules to the block. Two G1/4 ports connect it to the loop, and the built-in TFT shows coolant temperature and accumulated power-on time.

Fits
Desktop DDR5 with matching cooling armors
Capacity
Up to 4 RAM modules
Ports
2 × G1/4
Lighting
LRC 2.0 · 5V ARGB

Compatibility

Use one matching RAM cooling armor per memory module.

  • ✓Desktop DDR5 RAM fitted with Barrowch FBRAMLD-01 cooling armors

Plan for two or four modules. If your RAM already has heat spreaders, remove them before installing the armors.

Check your motherboard’s recommended DIMM slots and the clearance above them for the block, fittings, and tubing.

Design Highlights

Coolant temperature at a glance

The TFT shows real-time coolant temperature and accumulated power-on time. A round lens sits over the square TFT panel.

Either port can serve as the inlet

Coolant flows through wide microchannels in the nickel-plated copper base. Use either G1/4 port as the inlet to suit your tubing route.

5V addressable lighting

The LRC 2.0 lighting shines through the clear acrylic chamber below the aluminum cover. Use a compatible Barrow LRC 2.0 controller or a compatible adapter for a 5V 3-pin motherboard ARGB header.

Key Specifications

ModelFBRWB-PA4
Block dimensions (L × W × H)138 × 42 × 18.50 mm
Ports2 × G1/4, either port can be the inlet
Port center spacing81.50 mm
Cold plateNickel-plated copper
Coolant chamberClear acrylic
Top coverAluminum alloy
DisplayTFT, coolant temperature and accumulated power-on time
LightingBarrow LRC 2.0, 5V ARGB
Block colorsBlack or white

Manufacturer drawing. The arrows mark the G1/4 ports. Measurements are in millimeters.

Which Version Do I Need?

Barrowch FBRWB-PA4 RAM water blockTHIS PAGE
Choose Kit A for two modules or Kit B for four. Choose Just RAM block if you already have the matching armors.
Choose this single-module armor to complete a block-only order or replace one armor.
Choose this fan module if you want active air cooling for your RAM.

What's in the Box

Kit A   1 water block + 2 RAM cooling armorsKit B   1 water block + 4 RAM cooling armorsJust RAM block   1 water block

Each option is available with a black or white water block. The lighting controller is sold separately.

Installation & Use

1
Shut down and unplug the PC. Remove the memory modules and take off any stock heat spreaders.
2
Apply thermal pads at the chip contact points. Fit each module between the two halves of its cooling armor and secure the armor. Reinstall the modules in the slots specified by your motherboard manual.
3
Remove the two screws securing the block’s top cover. Lift off the cover, align the block body over the armors, and fasten it to them. Refit the cover.
4
Connect both G1/4 ports to your loop. Leak-test the loop before powering the PC.
5
Power the block through a compatible Barrow LRC 2.0 Aurora controller, or use the appropriate power adapter cable for a motherboard fan header or compatible 16-channel controller. For motherboard lighting, use an adapter for a 5V 3-pin ARGB header.

Have your DDR5 modules, matching armors for a block-only order, thermal pads for the installation, two G1/4 fittings, and a compatible power connection ready. You also need a loop with a pump, radiator, tubing, and coolant.

Manufacturer illustration. The block body is secured to the armors with the cover removed.

FAQ

Can I use this block with desktop DDR5 RAM?

Yes. Fit each DDR5 module with a Barrowch FBRAMLD-01 cooling armor before mounting the block.

Which option includes the RAM cooling armors?

Kit A includes two armors and Kit B includes four. Just RAM block includes the block only.

What does the TFT screen show?

It shows the temperature of the coolant in the block and accumulated power-on time.

Which fitting thread and inlet should I use?

Both ports take G1/4 fittings. Either port can be the inlet, so choose the orientation that suits your tubing.

What lighting connection does it need?

Use a compatible Barrow LRC 2.0 controller or a compatible adapter to a 5V 3-pin ARGB motherboard header. The controller is sold separately.

Product Gallery

Notes
  • Avoid pressing on the fragile TFT screen.
  • In case of product appearance structure upgrade, without further notice, in kind prevail.