Bykski · A-AR7900XTX-X
Full-cover GPU water block for ASRock RX 7900 XTX Taichi
The Bykski A-AR7900XTX-X is a full-cover water block for the ASRock Radeon RX 7900 XTX Taichi 24GB OC. It replaces the stock cooler and transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. The block comes with an aluminum backplate and uses G1/4 fittings.
Fits
ASRock RX 7900 XTX Taichi
Coverage
GPU core, memory, and VRM
Compatibility
The block fits the ASRock-specific PCB layouts listed below.
- ✓ASRock Radeon RX 7900 XTX Taichi 24GB OC (RX7900XTX TC 24GO)
- ✓ASRock Radeon RX 7900 XTX Phantom Gaming 24GB OC (RX7900XTX PG 24GO)
Before ordering, check your card’s model number and verify that its PCB layout matches the block.
ASRock Radeon RX 7900 XTX Taichi 24GB OC with its stock cooler.
Design Highlights
One cold plate for the core, memory, and VRM
The T2 copper cold plate picks up heat from the GPU die, memory chips, and voltage regulators. Jet microchannels pass coolant over the GPU contact area.
Clear acrylic top with G1/4 ports
The clear top lets you see the coolant path. Connect the loop to the G1/4 inlet and outlet and use a 5V 3-pin ARGB connection for the lighting.
Bykski’s PCB reference photo for the Taichi.
Mounting matched to the PCB
Compare your Taichi’s full PCB layout with the reference photo, including the mounting holes and component positions. For the Phantom Gaming model, verify the actual PCB before ordering.
Key Specifications
| Manufacturer model | A-AR7900XTX-X |
|---|
| Cold plate | T2 copper cold plate |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Black aluminum |
|---|
| Copper base beneath the GPU (Bykski design drawing) | 0.35 mm |
|---|
| Port thread | G1/4 |
|---|
| Water block (L × W × T) | 272.85 × 155.72 × 23.05 mm |
|---|
| Backplate (L × W × T) | 272.85 × 125.46 × 6.00 mm |
|---|
| Lighting | 5V 3-pin addressable RGB (RBW) |
|---|
Bykski drawing. Water block above, backplate below. Dimensions are in millimeters.
Which Version Do I Need?
Choose by the model number on your graphics card.
Bykski A-AR7900XTX-XTHIS PAGE
Choose this block for the listed ASRock Taichi or Phantom Gaming card once you verify the PCB.
Check this block if your card is a Sapphire Radeon RX 7900 XTX Nitro+.
Check this block if your card is a PowerColor Radeon RX 7900 XTX Red Devil 24GB.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplateThermal pad setMounting hardware set2 × G1/4 stop plugs1 × ARGB sync cable1 × screwdriver
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Included aluminum backplate.
Installation & Use
1Power off the system and remove the graphics card. Remove its stock cooler and backplate, then clean away the old thermal material.
2Cut the thermal pads to fit the matching memory and VRM contact points. Apply a thin layer of your own thermal paste to the GPU die.
3Align the block, PCB, and supplied backplate. Tighten the mounting screws evenly. If the holes do not line up, stop and check the fit.
4Connect the loop using G1/4 fittings and follow the inlet and outlet markings. Plug the lighting cable into a 5V 3-pin ARGB header.
5Run the pump with the card unpowered to check the loop for leaks before powering the card.
For a new loop, you also need a pump, reservoir, radiator, G1/4 fittings, tubing, and coolant.
Bykski assembly drawing. ① water block · ② thermal pads · ③ your card’s PCB · ④ spring screws · ⑤ backplate · ⑥ backplate screws.
FAQ
Does this block fit the ASRock RX 7900 XTX Phantom Gaming?
The 24GB OC model (RX7900XTX PG 24GO) is listed for this block. Verify your PCB layout before ordering.
Which fittings does the block use?
Use G1/4 fittings that match your tubing.
Can I connect the lighting to a 12V RGB header?
Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the LEDs.
Does the backplate need its own tubing?
The aluminum backplate mounts behind the PCB and stays outside the coolant path.
Where do the thermal pads go?
Place the supplied pads on the memory and VRM contact points shown in the installation diagram.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.
- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.