Bykski · A-GV9070GMOC-X
Full-cover water block for GIGABYTE RX 9070 XT GAMING OC
The Bykski A-GV9070GMOC-X replaces the stock cooler on supported GIGABYTE cards such as the Radeon RX 9070 XT GAMING OC 16G. In a custom liquid cooling loop, its nickel-plated copper cold plate carries heat from the GPU, memory, and power stages to the coolant. The included aluminum backplate mounts behind the circuit board.
Fits
GIGABYTE GAMING OC 16G (RX 9070 XT / RX 9070)
Cold plate
Nickel-plated T2 copper
Compatibility
Match the full GIGABYTE card model and part number.
- ✓GIGABYTE Radeon RX 9070 XT GAMING OC 16G (GV-R9070XTGAMING OC-16GD)
- ✓GIGABYTE Radeon RX 9070 GAMING OC 16G (GV-R9070GAMING OC-16GD)
Before ordering, verify your card’s exact PCB layout and mounting holes. See the PCB drawing under Installation & Use for the RX 9070 XT GAMING OC layout.
GIGABYTE Radeon RX 9070 XT GAMING OC 16G with its stock cooler.
Design Highlights
Coolant flow through the cold plate
Coolant flows through 0.3 mm jet microchannels in the copper cold plate. The clear acrylic top lets you see the channels.
Separate aluminum backplate
The black anodized backplate mounts to the rear of the card and stays outside the coolant path.
5V addressable RGB
Connect the lighting to a compatible 5V 3-pin ARGB header. Keep it off 12V 4-pin RGB headers.
Key Specifications
| Model (SKU) | A-GV9070GMOC-X |
|---|
| Cooling coverage | GPU core, memory, and voltage regulators (VRM) |
|---|
| Cold plate | Nickel-plated T2 copper |
|---|
| Top | Clear acrylic |
|---|
| Microchannels | 0.3 mm jet-type |
|---|
| Backplate | Black anodized aluminum, passive |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Lighting | 5V 3-pin ARGB (RBW) |
|---|
| Water block (L × W × T) | 219.95 × 149.47 × 26.25 mm |
|---|
| Backplate (L × W × T) | 219.95 × 119.47 × 5.98 mm |
|---|
Bykski dimension drawing. Water block above, backplate below. Measurements are in millimeters.
Which Version Do I Need?
Bykski A-GV9070GMOC-XTHIS PAGE
Choose this block for one of the GIGABYTE GAMING OC boards listed above after matching its PCB.
Check this separate block if you have a Sapphire Radeon RX 9070 NITRO+.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate1 × mounting hardware set1 × thermal pad set1 × 5V ARGB lighting strip2× G1/4 stop plugs
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the system, remove the card, and take off the stock cooler. Clean the old thermal material from the card.
2Peel the protective film from both sides of each thermal pad. Place the pads on the memory and power stages that meet the block’s raised surfaces. Apply your own thermal paste to the GPU die.
3Line up the mounting holes on the block, PCB, and backplate. Secure the assembly with the supplied hardware, tightening gradually and evenly.
4Connect the block to your loop with G1/4 fittings and seal any unused ports. Leak-test the loop with the card unpowered before switching on the system.
You also need a pump, reservoir, radiator, tubing, coolant, and G1/4 fittings that match your tubing.
Bykski installation drawing showing the board before thermal pads and paste are applied.
FAQ
Which water block fits the GIGABYTE RX 9070 XT GAMING OC 16G?
The A-GV9070GMOC-X fits the GV-R9070XTGAMING OC-16GD. Match your card’s PCB layout and mounting holes before ordering.
Does this water block also fit the GIGABYTE RX 9070 GAMING OC 16G?
Yes. The listed RX 9070 GAMING OC card is GV-R9070GAMING OC-16GD.
Is the backplate included?
Yes. The block comes with a passive black anodized aluminum backplate.
What fittings do I need?
Use G1/4 fittings sized for the tubing in your custom loop.
Which lighting header should I use?
Use a compatible 5V 3-pin ARGB header for the RBW strip.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.