Bykski · A-RX7900XT-X
Full-cover water block for the Radeon RX 7900 XT reference PCB
The Bykski A-RX7900XT-X replaces the stock cooler on the AMD Radeon RX 7900 XT reference PCB. Its copper cold plate transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. The block has a clear acrylic top and comes with a black aluminum backplate.
Fits
AMD RX 7900 XT reference
Compatibility
Match your card to the AMD reference PCB layout.
- ✓AMD Radeon RX 7900 XT 20GB (AMD reference PCB)
Not compatible:
- ✗AMD Radeon RX 7900 XTX (reference PCB)
- ✗Radeon RX 7900 XT with a non-reference PCB
Before ordering, check the full model name and compare the component layout and mounting holes with the PCB photo in the product gallery.
AMD Radeon RX 7900 XT reference card with its original cooler.
Design Highlights
Full-cover copper cold plate
The cold plate picks up heat at the GPU core, memory, and voltage regulators. Coolant carries that heat to the radiator in your loop.
Jet microchannels over the GPU core
Coolant passes through the fine channels in the cold plate above the GPU core.
Clear acrylic with 5V lighting
The clear top leaves the coolant channels visible. The included ARGB strip uses a 5V 3-pin connection.
Key Specifications
| Model | A-RX7900XT-X |
|---|
| Cold plate | T2 copper |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Black aluminum |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Inlet and outlet thread | G1/4 |
|---|
| Lighting connector | 5V 3-pin ARGB (Bykski RBW) |
|---|
| Water block (L × W × T) | 263.65 × 137.06 × 23.15 mm |
|---|
| Backplate (L × W × T) | 263.65 × 106.77 × 6.00 mm |
|---|
Bykski dimension drawing in millimeters. Water block above, backplate below.
Which Version Do I Need?
Start with the full name on your graphics card. Each of these blocks has its own PCB fit list.
Bykski A-RX7900XT-XTHIS PAGE
Choose this block for the AMD Radeon RX 7900 XT reference PCB.
For ASUS TUF Gaming Radeon RX 7900 XT OC or RX 7900 XTX OC cards.
For the ASRock Radeon RX 7900 XTX Taichi 24GB OC.
What's in the Box
1 × GPU water block1 × aluminum backplate2 × G1/4 stop plugsThermal padsMounting hardware set1 × 5V ARGB strip1 × ARGB sync cable
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the PC. Remove the graphics card and its stock cooler, then clean away the old thermal materials.
2Check that the block matches the PCB and its mounting holes. Cut the supplied pads to fit the marked memory and power delivery areas. Apply a thin layer of your own thermal paste to the GPU die.
3Align the block, PCB, and backplate. Start the mounting screws by hand and tighten them gradually in a cross pattern. Secure the backplate with its screws.
4Connect the loop with G1/4 fittings and close the unused ports with the stop plugs. For lighting, align the sync cable with the 5V mark on a 5V 3-pin ARGB header.
5Leak-test the loop with the graphics card unpowered.
Your loop also needs a pump, radiator, G1/4 fittings, tubing, and coolant.
Bykski’s thermal material placement diagram. The shaded areas around the GPU die show where to place the pads.
FAQ
Will this block fit an RX 7900 XTX?
No. A-RX7900XT-X fits the AMD Radeon RX 7900 XT reference PCB. Check your exact XTX model for a matching block.
Will it fit a partner-brand RX 7900 XT?
Confirm that your card uses the AMD reference PCB. Compare the board layout and mounting holes with the photo in the product gallery before ordering.
Does it come with a backplate?
Yes. One black aluminum backplate is included.
Can I connect the lighting to a 12V RGB header?
Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the LED strip.
Which fittings do I need?
Use G1/4 fittings that match your tubing. Two G1/4 stop plugs are included for unused ports.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.
- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.