Bykski · A-XF7900XTX-X
Full-cover water block for the XFX RX 7900 XTX MERC 310
The Bykski A-XF7900XTX-X replaces the stock cooler on the XFX Speedster MERC 310 Radeon RX 7900 XTX Black Edition. It carries heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. This version includes an aluminum backplate and uses G1/4 ports and 5V addressable RGB lighting.
Fits
XFX MERC 310 XTX Black Edition
Compatibility
Confirmed graphics card
- ✓XFX Speedster MERC 310 Radeon RX 7900 XTX Black Edition 24 GB (RX-79XMERCB9)
The matched PCB shown here has three 8-pin PCIe power sockets. Before ordering, check your card’s exact model number and compare the full PCB layout and mounting holes with the photo.
Bykski’s photo of the XFX MERC 310 RX 7900 XTX PCB.
Design Highlights
Coverage for the GPU, memory, and VRM
The copper cold plate has separate contact areas for the GPU die, memory chips, and voltage regulators.
Jet microchannels under a clear cover
Coolant flows through the jet microchannels in the cold plate. You can see the fins and coolant path through the clear acrylic cover.
5V addressable lighting
Use the lighting sync cable with a 5V 3-pin ARGB motherboard header or use a compatible 5V ARGB controller.
Key Specifications
| Bykski model | A-XF7900XTX-X |
|---|
| Cooling coverage | GPU core, graphics memory, and VRM |
|---|
| Cold plate | T2 copper |
|---|
| Top cover | Clear acrylic |
|---|
| Microchannel gap | 0.5 mm |
|---|
| Backplate | Black aluminum backplate, outside the coolant path |
|---|
| Inlet and outlet thread | G1/4 |
|---|
| Water block (L × W × T) | 286.61 × 147.70 × 23.25 mm |
|---|
| Backplate (L × W × T) | 286.61 × 116.76 × 6.00 mm |
|---|
| Lighting | 5V 3-pin ARGB (RBW) |
|---|
Bykski dimension drawing. Water block above, backplate below. All dimensions are in millimeters.
Which Version Do I Need?
Check the graphics card brand and PCB before choosing a block for an RX 7900 XTX.
Bykski A-XF7900XTX-XTHIS PAGE
Choose this block for the XFX MERC 310 Black Edition PCB shown above.
For an ASUS TUF Gaming Radeon RX 7900 XTX, check this model’s compatibility list for your PCB.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × lighting sync cable
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Bykski assembly drawing. 1 Water block · 2 Thermal pads · 3 Your graphics card PCB · 4 Block screws · 5 Backplate · 6 Backplate screws.
Installation & Use
1Shut down the system and remove the card. Take off the original cooler and backplate, then clean off the old thermal material.
2Cut the supplied thermal pads to fit the red-outlined areas in the diagram. Remove the pads’ protective film and place the pads on those areas. Apply your own thermal paste to the GPU die outlined in blue.
3Align the block and backplate with the PCB mounting holes and tighten the screws gradually and evenly.
4Connect your tubing with G1/4 fittings at the marked inlet and outlet. Cap the unused ports with the stop plugs.
5If you plan to use the lighting, connect the sync cable to a 5V 3-pin ARGB header.
6Keep the graphics card unpowered while you run the pump and leak-test the loop.
You also need a pump, reservoir, radiator, G1/4 fittings, tubing, and coolant.
Bykski thermal material placement diagram. Red outlines mark the pad locations. The blue outline marks the GPU die for paste.
FAQ
How do I tell whether my XFX MERC 310 fits?
Check the card’s model number for RX-79XMERCB9 and match its PCB to the photo above before ordering.
What pad thickness does Bykski specify?
Bykski’s installation diagram for A-XF7900XTX-X specifies 1.5 mm pads. Cut the supplied pads to fit the red-outlined locations in the diagram.
What fittings does the block take?
Use G1/4 fittings for the inlet and outlet, and seal the remaining openings with the supplied stop plugs.
Which motherboard header do I use for the lighting?
Use a 5V 3-pin ARGB header and align the cable’s arrow with the 5V pin. A 12V 4-pin RGB header can damage the LEDs.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.