Bykski · B-FRD-XSN260
360 mm liquid cooling for the MetaX N260
The Bykski B-FRD-XSN260 is an all-in-one liquid cooler for the 64GB MetaX Xisi N260 PCIe GPU. A full-cover copper cold plate replaces the stock cooler, and an inline pump moves heat to a 360 mm radiator. The kit lets you make that change in an inference workstation with room for the radiator and tubing.
Compatibility
- ✓MetaX (MUXI) Xisi N260 64GB PCIe, full-height, full-length, dual-slot card with the XSN260 PCB
Compare the mounting holes and component layout on your PCB with the diagram before ordering.
Bykski PCB diagram for the XSN260 layout.
Design Highlights
Bykski cold plate illustration.
Full-cover copper cold plate
The T2 copper plate picks up heat at the GPU. Its 0.3 mm microchannels give the coolant more surface area to flow over.
Bykski view of the assembled loop.
Pump in the tubing
The inline pump circulates coolant between the GPU block and the chassis-mounted radiator. When planning the radiator position, leave enough room for the tubes to curve freely.
Key Specifications
| Standard 360 mm kit | Bykski B-FRD-XSN260-360 |
|---|
| Cooler type | All-in-one GPU liquid cooler |
|---|
| Cold plate | T2 copper, 401 W/(m·K) nominal material conductivity |
|---|
| Microchannels | 0.3 mm, up to 44 channels |
|---|
| Radiator | 360 mm class, aluminum, 12 coolant channels |
|---|
| Inline pump | 7,000 RPM, 450 L/h nominal flow, 7 m head |
|---|
Bykski radiator illustration.
Which Version Do I Need?
Choose the cooling setup that matches your workstation.
Bykski B-FRD-XSN260 360 mm AIOTHIS PAGE
Choose this kit if you want a preassembled cooling loop for an N260 and your chassis has a 360 mm radiator mount.
Choose the standalone block if you already have a custom loop or plan to source your own pump, reservoir, radiator, tubing, fittings, and coolant.
What's in the Box
1× full-cover GPU block1× 360 mm radiator3× radiator fans1× inline pumpConnected tubing
The list describes the standard 360 mm kit.
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
Bykski view of the 360 mm assembly.
Installation & Use
1For the standard 360 mm kit, switch off the system, remove the GPU, and take off its original cooler. Clean the old thermal paste and pad residue.
2Apply a thin layer of GPU thermal paste to the die. Place thermal pads on the contact areas marked in the mounting diagram, using the thickness specified for your kit.
3Align the mounting holes and secure the block, tightening the screws evenly. If your kit includes a backplate, line it up with the rear mounting holes and secure it with the matching screws.
4Mount the radiator and fans at the chassis’s 360 mm position. Route the tubes without sharp bends. Confirm the connector types and power requirements for the supplied pump and fans before connecting them.
5Inspect the tubing connections for leaks before powering the GPU. On first startup, verify that the pump and fans run.
You will also need your own GPU thermal paste and a chassis with a 360 mm radiator mount. Check clearance for the fans and tubing, and ask customer service to confirm the pad thickness for your kit before installation.
Bykski placement diagram. Apply paste to the die and pads to the shaded power component areas.
FAQ
Do I need a separate pump?
The standard 360 mm kit includes an inline pump as part of the preassembled loop.
Will this cooler fit my workstation case?
Check for a 360 mm radiator mount. Allow space behind the mount for the fan stack and at the hose end for the tubing to turn without kinking.
Can I identify a compatible N260 by its stock cooler?
MetaX offers an active-cooled N260 for workstations. Match your card’s mounting holes and component layout to the XSN260 diagram.
Notes- For any questions, please contact customer service.