AMD Radeon Instinct MI50 360 mm GPU AIO Liquid Cooler | Bykski B-FRD-MI50

Bykski · B-FRD-MI50

360 mm GPU AIO liquid cooler for the AMD Radeon Instinct MI50

The Bykski B-FRD-MI50 all-in-one liquid cooler replaces the stock cooler on an AMD Radeon Instinct MI50 with the PCB shown below. Bykski shows the single-card kit with an inline pump that circulates coolant between the GPU block and a 360 mm radiator. Choose B-FRD-MI50-360 for one matching MI50 or B-FRD-MI50-360-H for two.

Fits
AMD Radeon Instinct MI50
Radiator class
360 mm
Single-card cold plate
T2 copper
Configurations
Single card or dual card

Compatibility

  • ✓AMD Radeon Instinct MI50 with the PCB layout shown

Before ordering, compare the entire PCB and mounting-hole positions on each card with Bykski’s photo.

Check your case’s 360 mm radiator mount, allow 63 mm of clearance for the radiator and fans, and leave room to route the tubing.

Bykski’s MI50 PCB photo for comparison.

Design Highlights

Standard single-card kit shown.

Standard single-card assembly

Bykski shows the pump inline on the tubing and three fans mounted on the radiator.

T2 copper cold plate

In Bykski’s single-card design, the cold plate contacts the GPU chip through thermal paste.

0.3 mm jet microchannels

Bykski’s single-card cold plate uses fine channels to give the coolant more surface area to pick up heat.

Key Specifications

ModelBykski B-FRD-MI50
Single-card kitB-FRD-MI50-360 · one matching MI50
Dual-card kitB-FRD-MI50-360-H · two matching MI50 cards
ColorBlack
Single-card cold plateT2 copper with 0.3 mm jet microchannels
Radiator and fan clearance (both kits)360 mm radiator, 38 mm thick. With 25 mm fans fitted, allow 63 mm of clearance.
Single-card fans shown3
Single-card tubing shownBraided
Single-card block drawing (L × W × T)266.46 × 117.01 × 26.07 mm
Radiator length in earlier single-card drawing396 mm

Bykski’s single-card block drawing. Dimensions are in millimeters.

Which Version Do I Need?

Choose according to how many matching MI50 cards you plan to cool and the type of loop you’re building.

B-FRD-MI50-360THIS PAGE
Choose this kit to liquid-cool one MI50 with the PCB shown above.
B-FRD-MI50-360-HTHIS PAGE
Choose this kit for two MI50 cards that each match the pictured PCB.
Choose the standalone MI50 water block if you’re connecting it to a custom loop.

What's in the Box

B-FRD-MI50-360 · 1 × GPU water block and 1 × dedicated backplateB-FRD-MI50-360-H · 2 × GPU water blocks and 2 × dedicated backplates

Each kit also includes 1 × 360 mm radiator, 3 × 120 mm fans, a pump, thermal pads, and mounting hardware.

Bykski connects the tubing and fills the loop with coolant at the factory.

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Standard Single-Card Installation

1
Shut down the system, remove the card and its original cooler, and clean away the old thermal material.
2
Follow the installation instructions supplied with this kit for thermal pad placement. Apply your own thermal paste to the GPU chip.
3
Fit the spacers over the block’s mounting posts, then align the posts with the PCB holes and secure the assembly as instructed.
4
Mount the radiator and route the tubing. Connect the pump and fans according to the instructions for your kit, then check that they’re running before putting the card under load.

Have a screwdriver and your own thermal paste ready. Before starting, check the included thermal pads and make sure you have room to mount the radiator.

FAQ

How do I tell whether this AIO fits my MI50?

Match your AMD Radeon Instinct MI50 PCB and its mounting holes to Bykski’s photo above.

Which kit do I need for one or two MI50 cards?

Choose B-FRD-MI50-360 for one matching MI50 or B-FRD-MI50-360-H for two.

What does Bykski show in the standard single-card kit image?

The B-FRD-MI50-360 image shows a GPU block, a radiator with three fans, and an inline pump on the connected tubing.

What is involved in installing the standard single-card kit?

You remove the original cooler, fit the thermal materials and water block, then mount the radiator and connect the pump and fans.

How much room do the radiator and fans need?

Both kits use a 360 mm radiator and require 63 mm of clearance for the radiator and fans. The earlier single-card drawing shows an overall radiator length of 396 mm. Leave room to route the tubing.

Notes
  • If the block doesn’t line up with your PCB, stop and contact support before tightening the screws.