RTX A5000 AIO Liquid Cooler for Leadtek 24GB PCIe | Bykski B-FRD-RTXA5000

Bykski · B-FRD-RTXA5000

All-in-one liquid cooling for the Leadtek RTX A5000

The Bykski B-FRD-RTXA5000 is an all-in-one GPU liquid cooler for the Leadtek NVIDIA RTX A5000 24GB desktop graphics card. Its full-cover block replaces the factory blower and transfers heat from the GPU, memory, and power circuitry to a case-mounted radiator. An inline pump circulates coolant through the connected loop.

Fits
Leadtek RTX A5000 24GB
Cold plate
T2 copper
Pump
Inline
Radiator
Aluminum

Compatibility

Bykski lists this PCB layout.

  • ✓Leadtek NVIDIA RTX A5000 24GB (full-height desktop PCIe card)

Before ordering, compare your card’s mounting holes and component layout with the bare PCB shown in the product gallery.

Leadtek RTX A5000 with the stock cooler installed. Photo from Leadtek.

Design Highlights

Copper contact across the board

The T2 copper cold plate covers the GPU die, memory, and power components. Thermal pads make contact with the memory and power components.

Microchannels in the cold plate

The 0.3 mm jet microchannels increase the area in contact with coolant inside the block.

Bykski illustration of the 360 mm configuration.

Pump between the block and radiator

The inline pump moves coolant through the braided hoses. The aluminum radiator and its fans release the heat at the case mount.

Key Specifications

ModelB-FRD-RTXA5000
Cooling systemFull-cover GPU AIO
Cold plateT2 copper
Microchannels0.3 mm
Coolant pathInline pump and braided hoses
Radiator materialAluminum
Radiator formats (drawings)120 / 240 / 360 mm
Radiator lengths (drawings)156 / 276 / 396 mm, respectively
Water block (L × W × H)259.70 × 97.68 × 18.00 mm

Bykski water block drawing. Dimensions are in millimeters.

Which Version Do I Need?

Start with the PCB match. Then check the space in your case for the radiator, fans, and hose routing.

Bykski B-FRD-RTXA5000THIS PAGE
Choose this AIO if you want the GPU block, pump, and radiator connected in one assembly.
Choose the full-cover water block with backplate if you’re adding the same Leadtek card to a custom loop.

What's in the Box

GPU AIO assembly with full-cover blockInline pump and connected hosesFan-cooled radiator

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Check radiator clearance with the fans in place and plan the hose path. Bykski shows a top-mounted radiator as one example.
2
Remove the stock cooler and clean away old paste and pad residue.
3
Place thermal pads on the memory and power components shown in the installation diagram. Apply your own GPU thermal paste to the GPU die.
4
Set the block flat on the board. Align the mounting holes and tighten the screws evenly.
5
Secure the radiator and route the hoses without pulling on the fittings. Connect the pump and fans according to their connectors. Inspect the loop for leaks before powering the GPU and confirm that the pump and fans run on startup.

Have your own GPU thermal paste and the pads specified for your mounting kit ready. The AIO uses its own inline pump.

Bykski installation drawing. The areas around the die take pads. The center die takes GPU thermal paste.

FAQ

Do I need a separate pump for this RTX A5000 AIO?

The pump is already in the tubing between the GPU block and radiator.

What should I measure in my case?

Check the length and mounting pattern for the selected radiator, the depth with fans attached, and the room to route the hoses to the card.

What does the water block cool?

It draws heat from the GPU die, memory, and power circuitry. The installation diagram shows where the pads and paste go.

How can I identify the right RTX A5000?

Look for the Leadtek NVIDIA RTX A5000 24GB desktop card, then compare its bare PCB with the board photo in the product gallery.

Notes
  • If the block does not sit flat or the screw holes do not line up, stop and recheck the PCB and mounting parts before tightening.