Bykski · B-FRD-RTX4090
360 mm liquid cooling for RTX 4090 Turbine and Leadtek boards
The Bykski B-FRD-RTX4090 is a 360 mm all-in-one liquid cooler for GeForce RTX 4090 24 GB Turbine and Leadtek cards with the matching PCB. Its full-cover block replaces the stock cooler and transfers heat from the GPU, memory, and power stages to a radiator mounted in the case.
Fits
RTX 4090 24 GB Turbine / Leadtek
Compatibility
Bykski lists these PCB layouts
- ✓NVIDIA GeForce RTX 4090 24 GB GDDR6X Turbine
- ✓Leadtek GeForce RTX 4090 24 GB with Bykski’s listed PCB layout
Compare the mounting holes and component layout on your card with the PCB photo before ordering.
PCB photo from Bykski’s compatibility guide.
Design Highlights
Inline pump and case-mounted radiator
The pump sits in the tubing between the GPU block and the aluminum radiator. The three radiator fans on the standard kit move air through the fins to remove heat from the loop.
Copper cold plate over three heat sources
The T2 copper cold plate uses 0.3 mm jet microchannels. The block contacts the GPU die and uses thermal pads at the memory and MOSFET power stages.
Key Specifications
| Model | Bykski B-FRD-RTX4090 |
|---|
| Cooler type | Full-cover GPU AIO with backplate |
|---|
| Cold plate | T2 copper |
|---|
| Jet microchannels | 0.3 mm |
|---|
| Block dimensions | 287.33 × 98.43 × 16 mm |
|---|
| Radiator | 360 mm class, aluminum |
|---|
| Radiator fans | 3 shown on the standard 360 mm kit |
|---|
| Pump position | Inline in the tubing |
|---|
Block dimensions from the manufacturer drawing.
Which Version Do I Need?
Match your card’s PCB first, then check the radiator space in your case.
Bykski B-FRD-RTX4090THIS PAGE
Choose the standard B-FRD-RTX4090-360 for a single matching Turbine or Leadtek card. For a dual-card build, confirm the kit configuration with us before ordering the B-FRD-RTX4090-360-H thick-radiator option.
Choose this separate AIO if your GeForce RTX 4090 matches the AIC Reference PCB shown on its product page.
What's in the Box
Full-cover GPU block and backplate360 mm radiator with inline pump and connected tubingRadiator fans (standard 360 mm kit)
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
Installation & Use
1Shut down and unplug the PC. Remove the graphics card, take off its stock cooler, and clean off the old thermal material.
2Place thermal pads on the memory and MOSFET locations shown in the diagram. Apply GPU thermal paste to the GPU die.
3Align the water block and backplate with the card's mounting holes and tighten the screws evenly.
4Mount the radiator and fans in a 360 mm case position. Check clearances and route the tubing without sharp bends.
5Connect power to the inline pump and radiator fans. At startup, confirm the pump and fans run and check the tubing connections for leaks.
You also need your own GPU thermal paste, a screwdriver, and a case with clearance for the radiator, fans, and tubing.
Shaded strips mark the thermal pad locations. The center die takes GPU thermal paste.
FAQ
Can I water-cool my RTX 4090 with this kit?
Yes, if it’s the 24 GB Turbine or Leadtek card and the PCB matches Bykski’s compatibility photo.
Do I need a separate pump for this RTX 4090 AIO?
The pump comes in the assembled cooling circuit with the tubing and radiator. No separate pump or reservoir is needed.
Will the 360 mm radiator fit my case?
Check for a 360 mm radiator mount and enough room for the radiator, fans, and tubing. Bykski shows a top-mounted radiator in its example.
What does -360-H mean on the size selector?
It denotes the 360 mm thick-radiator option listed for dual-card builds. Confirm the kit configuration before ordering for two GPUs.
Notes- If the block does not line up with your card, stop and confirm the PCB layout before tightening the screws.