Iluvatar CoreX TianGai 150 (BI-V150) AIO Liquid Cooler, Bykski B-FRD-BIV150

Bykski · B-FRD-BIV150

All-in-one liquid cooling for the Iluvatar BI-V150

The Bykski B-FRD-BIV150 is an all-in-one liquid cooler for the 64 GB Iluvatar CoreX TianGai 150 (BI-V150) PCIe accelerator with the BIV150 PCB. It replaces the stock passive heatsink with a full-cover water block. In the standard 360 mm kit, an inline pump circulates coolant to a fan-cooled radiator mounted in the case.

Fits
Iluvatar BI-V150
Standard radiator
360 mm
Cold plate
T2 copper

Compatibility

  • ✓Iluvatar CoreX TianGai 150 (BI-V150), PCIe, 64 GB HBM2e, BIV150 PCB layout

Before ordering, compare your card’s PCB and mounting holes with the board shown here.

Bykski’s BIV150 PCB photo

Design Highlights

Pump in the tubing

On the standard B-FRD-BIV150-360, the inline pump circulates coolant through braided tubing between the GPU block and the radiator. Radiator fans move air through the fins to carry heat out of the loop.

Full-cover metal block

The T2 copper cold plate follows the BIV150 board layout. Bykski’s installation diagram shows where to apply paste to the chips and place pads over the power components.

Parallel microchannels

Bykski specifies up to 44 parallel 0.3 mm microchannels in the cold plate to increase the surface area in contact with coolant.

Key Specifications

ModelBykski B-FRD-BIV150
Cooling typeFull-cover GPU AIO
Block constructionAll-metal block with T2 copper cold plate
Block dimensions278.19 × 106.68 × 16.60 mm
Standard radiator mount360 mm
Pump (standard 360 mm)Bykski’s illustrated spec: 7,000 RPM, 450 L/h flow, 7 m head
Stock card form factorFull-length, full-height, dual-slot PCIe
Stock card board power350 W

Bykski’s block dimensions

Which Version Do I Need?

This page offers two 360 mm options. Choose by card count and radiator clearance.

Bykski B-FRD-BIV150-360
Standard 360 mm AIO for one matching card.
Bykski B-FRD-BIV150-360-H
360 mm thick-radiator option for two cards. Verify both PCB layouts and the mounting depth available for the radiator and fans.

For a custom loop, see the Bykski IC-BIV150-SR water block with backplate for the TianGai 150.

What’s in the Box

Bykski B-FRD-BIV150 GPU AIO kit

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Shut the system down, remove the accelerator and its stock heatsink, and clean off the old thermal compound.
2
Use your own GPU thermal paste on the chip surfaces and fit the thermal pads over the power components as shown in Bykski’s installation diagram.
3
Line up the block with the PCB screw holes and secure it. If your setup uses a backplate, align and fasten it as shown in Bykski’s installation diagram.
4
Reinstall the card and secure the radiator to a case mount with enough space for the fans and tubing bends.
5
Follow the kit’s startup instructions and connect the pump and fans to power connections that match their leads. Check the tubing connections for leaks and confirm the pump and fans are running before putting the card under load.

You’ll also need your own GPU thermal paste, a screwdriver, and a case with room for the accelerator, radiator, fans, and tubing.

Bykski’s top-mount example

FAQ

How is the Iluvatar BI-V150 cooled from the factory?

The BI-V150 uses a passive heatsink that relies on chassis airflow. The AIO replaces that heatsink and moves heat to a radiator with fans.

Where is the pump on the standard 360 mm AIO?

The pump sits in the tubing between the GPU block and the radiator.

Will the standard 360 mm kit fit my case?

Look for a 360 mm radiator mount. Compare the case’s available space with the radiator’s overall length and the depth with fans installed, and allow room for the tubing to bend.

What does the -H suffix mean on this listing?

B-FRD-BIV150-360-H is the 360 mm thick-radiator option listed for two cards. Check the available mounting depth before choosing it.

Notes
  • If the block does not sit flat or the screw holes do not line up, stop and check the PCB layout before tightening.