Enflame S60 GPU AIO Liquid Cooler, 360 mm | Bykski B-FRD-SYS60

Bykski · B-FRD-SYS60

360 mm AIO liquid cooler for the Enflame S60

The Bykski B-FRD-SYS60 is an all-in-one liquid cooler for the Enflame S60 PCIe inference accelerator. It replaces the stock air cooler with a full-cover water block connected by tubing to an inline pump and a 360 mm radiator. Coolant carries heat from the card to the radiator mounted in the chassis.

Fits
Enflame S60 PCIe
Radiator
360 mm
Cold plate
Nickel-plated T2 copper
Pump
Inline

Compatibility

Bykski lists this PCB layout

  • ✓Enflame S60 48 GB PCIe inference accelerator (S60 PCB layout)

Verify your exact card model and PCB layout before ordering.

Enflame’s product image shows the S60 with its stock cooler.

Design Highlights

Three-fan layout shown for the 360 mm radiator

Bykski specifies an aluminum radiator with 12 coolant channels. Check the radiator’s full length and its depth with the fans you plan to use.

Pump mounted in the tubing

The inline pump sits between the radiator and the water block. Leave space for the pump when planning how to route the braided tubing.

Full-cover cold plate

The nickel-plated T2 copper cold plate cools the accelerator chip. Thermal pads transfer heat from the memory and power circuitry to the block. Coolant passes through 0.3 mm jet microchannels.

Key Specifications

Single-card modelB-FRD-SYS60-360
Cold plateT2 copper with electroless nickel plating
Cold plate microchannels0.3 mm
Block size (L × W × T)279.07 × 106.66 × 16 mm
Radiator360 mm, aluminum, 12 coolant channels
Radiator length396 mm
Radiator depth with fans63 mm as illustrated
Radiator fan layoutThree fans shown
Inline pump (manufacturer specifications)7,000 RPM, 450 L/h, 7 m head
TubingBraided, attached to the block and radiator

Manufacturer drawing for the single-card kit. Dimensions are in millimeters. The 480 mm mark is the span shown in this layout.

Which Version Do I Need?

Match the option to the number of S60 cards you plan to cool. The dimensions shown are for the single-card kit.

B-FRD-SYS60-360THIS PAGE
Select “360mm” to cool one Enflame S60.
B-FRD-SYS60-360-H
Select “360mm Thick row(Dual Graphics Cards)” to cool two matching Enflame S60 cards.

What’s in the Box (Single-Card Kit)

1 × Bykski B-FRD-SYS60-360 AIO liquid cooler

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Remove the S60’s stock cooler and clean old paste and pad residue from the card.
2
Apply thermal pads to the memory and power components at the block’s contact points. Apply your own GPU thermal paste to the accelerator chip.
3
Align the water block with the PCB mounting holes. If your kit has a backplate, follow Bykski’s instructions to align and fasten it. Stop if the holes or contact points do not line up.
4
Mount the radiator and fit compatible fans. Route the tubing so it reaches the block without kinks and leaves space for the inline pump.
5
Connect the pump and fans to suitable power connections. Check for leaks and verify that the pump and fans run before putting the card under load.

Have GPU thermal paste and correctly sized thermal pads ready. Plan for a 360 mm radiator mount, compatible radiator fans and suitable power connections for the pump and fans.

Bykski illustration of a top-mounted radiator and tubing route.

FAQ

Is this a universal GPU AIO?

Bykski lists the Enflame S60 PCIe inference accelerator with the S60 PCB layout. Verify your board before ordering.

How is the S60 originally cooled?

The 300 W PCIe S60 uses a passive air heatsink that relies on chassis airflow.

Do I need a separate pump?

The single-card design uses an inline pump in the tubing between the radiator and the water block.

How much case clearance does the single-card kit need?

Check for a 360 mm radiator mount with room for the 396 mm radiator. Bykski’s illustrated fan layout is 63 mm deep. Check the depth with your chosen fans and leave room for the tubing and inline pump.

Notes
  • Check radiator and tubing clearance in your case before removing the stock cooler.