Bykski · N-TESLA-T4-X
Full-cover water block for the NVIDIA Tesla T4
The Bykski N-TESLA-T4-X is a full-cover water block and backplate for the NVIDIA Tesla T4 16 GB PCIe accelerator. It replaces the stock passive heatsink, which depends on airflow from the chassis. The block cools the GPU, memory, and power components by transferring their heat to the coolant in a custom loop.
Fits
NVIDIA Tesla T4 16 GB PCIe
Cold plate
Nickel-plated T2 copper
Compatibility
- ✓NVIDIA Tesla T4 16 GB GDDR6 PCIe
Not compatible:
Before ordering, send us a clear photo of your card’s bare PCB so we can check fit.
Stock NVIDIA Tesla T4 shown for identification (Lenovo product photo).
Design Highlights
Nickel-plated copper cold plate
The T2 copper cold plate draws heat from the GPU core, memory, and power MOSFETs. Coolant flows through 0.3 mm jet microchannels in the cold plate.
Separate aluminum backplate
The included black aluminum backplate mounts behind the card. Coolant flows through the water block on the front of the PCB.
Key Specifications
| Model | N-TESLA-T4-X |
|---|
| Cold plate | Nickel-plated T2 copper |
|---|
| Other block material | POM |
|---|
| Backplate | Black aluminum |
|---|
| Port layout | Inlet and outlet on the same end |
|---|
| Water block (L × W × T) | 201.41 × 100.92 × 16.50 mm |
|---|
| Backplate (L × W × T) | 167.55 × 61.38 × 2.00 mm |
|---|
Bykski drawing in millimeters. Water block above, backplate below.
Which Version Do I Need?
Start with your card's PCB layout and decide whether you want to build a custom loop or use an all-in-one cooler.
Bykski N-TESLA-T4-XTHIS PAGE
Choose this block for a custom loop once we confirm fit from a photo of your Tesla T4’s bare PCB.
This custom-loop block lists both Tesla P4 and Tesla T4. Match your card to the PCB layout on that listing.
Choose this Tesla T4 cooler for a kit with the block, pump, tubing, and radiator already connected. Check your case for a 360 mm radiator mount.
What's in the Box
1 × full-cover water block1 × aluminum backplate5 × 1.5 mm thermal pad strips4 × 0.5 mm washers4 × spring screws6 × backplate screws
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
Installation & Use
1Shut down the system, remove the card, and take off the stock heatsink. Clean off the old thermal material.
2Cut the 1.5 mm thermal pads to fit the memory and power MOSFET contact areas shown in the Bykski instructions. Apply your own GPU thermal paste to the die.
3Align the water block, PCB, and backplate. Secure them with the supplied hardware as shown in the assembly diagram.
4Use matching fittings to connect your tubing to the block’s marked inlet and outlet.
5Fill the loop and run the pump for a leak test while the rest of the system stays off.
You also need a pump, reservoir, radiator with fans, tubing, matching fittings, and coolant.
1 water block · 2 thermal pads · 3 your GPU board · 4 washers · 5 spring screws · 6 backplate · 7 backplate screws
FAQ
How is the Tesla T4 cooled from the factory?
The stock Tesla T4 uses a passive heatsink that depends on chassis airflow. This block transfers heat into a custom liquid-cooling loop.
Will the water block fit my case?
Use the dimension drawing to check space for the block, fittings, and tubing. If you're building a new loop, also check the radiator mounting space.
Do I need a separate pump and radiator?
Yes. Connect the block to a custom loop with a pump, reservoir, radiator and fans, fittings, tubing, and coolant.
What thickness of thermal pads should I use?
Bykski specifies 1.5 mm pads at the memory and power MOSFET contact points shown in its installation diagram.
Notes- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.