Tesla V100 32GB PCIe Waterblock with Backplate | Bykski N-TESLA-V100-32G-X-V2

Bykski · N-TESLA-V100-32G-X-V2

Full-cover water block for the Tesla V100 32GB PCIe

The Bykski N-TESLA-V100-32G-X-V2 is a full-cover GPU water block with an aluminum backplate for NVIDIA Tesla V100 32GB PCIe cards that match the Bykski PCB reference in the second product gallery image. It replaces the stock cooler and transfers heat from the GPU, memory, and power stages to a custom liquid cooling loop during sustained workloads.

Fits
Tesla V100 32GB PCIe · Bykski PCB match required
Cold plate
T2 copper
Ports
Rear G1/4
Backplate
Aluminum

Compatibility

  • ✓NVIDIA Tesla V100 32GB PCIe (PCB must match the Bykski reference)

Before ordering, compare your exact card model and full PCB layout with the Bykski reference in the second product gallery image.

Design Highlights

Full-cover copper cold plate

The T2 copper cold plate draws heat from the GPU, memory, and power stages. Coolant flows through jet microchannels with 0.5 mm gaps between the fins.

Rear ports for flexible tubing

The rear G1/4 ports sit in a black POM terminal. Either port can serve as the inlet, so you can choose the flow direction that suits your tubing route. The rear placement is designed to leave room for the NVLink bridge.

Key Specifications

Model (SKU)N-TESLA-V100-32G-X-V2
Cold plateT2 high-purity copper
Front panelStainless steel
Port terminalBlack POM
Port threadG1/4
BackplateAluminum
Block dimensions (L × H × T)267.55 × 95.40 × 21.70 mm
Backplate dimensions (L × H × T)266.73 × 106.75 × 6.0 mm
Microchannel gap0.5 mm
Finish colorBlack and gunmetal
LightingNone

Block dimensions in millimeters (manufacturer drawing).

Which Version Do I Need?

Both are custom-loop blocks with backplates. Compare your PCB with the reference image for the block you choose and check the tubing route in your case.

N-TESLA-V100-32G-X-V2THIS PAGE
Choose the X-V2 if either rear port might need to serve as the inlet in your loop.
Choose the SR if your tubing can reach its designated inlet. Use the inlet marked on the SR diagram.

Tesla V100 models vary by memory size and board layout. Check your exact model and PCB before choosing a block.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate5 × 1.2 mm thermal pad strips8 × 0.5 mm insulating washers8 × spring screws5 × backplate screws1 × M2 nut1 × M2 screwPort plug hardware

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Manufacturer assembly diagram. 1 block · 2 thermal pad strips · 3 your graphics card PCB · 4 insulating washers · 5 spring screws · 6 backplate · 7 backplate screws · 8 M2 nut · 9 M2 screw.

Installation & Use

1
Power down the system and remove the card. Remove the stock cooler, clean off the old thermal material, and check that the block's mounting holes line up with the PCB.
2
Trim the 1.2 mm thermal pads to fit the memory and MOSFET contact areas shown by Bykski. Leave the inductors bare. Apply thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Place insulating washers at the four holes around the GPU. Tighten the spring screws gradually in a diagonal pattern, then secure the remaining backplate holes.
4
Connect the tubing with G1/4 fittings and fill the loop. Leak-test with only the pump powered. Power on the card after confirming the loop is leak-free.

You also need G1/4 tubing fittings, tubing, a pump, a reservoir, a radiator with fans, and coolant.

Manufacturer diagram. The dark strips on the right show the MOSFET pad positions. Apply paste to the GPU die.

FAQ

What type of cooling does this Tesla V100 waterblock provide?

It replaces the stock cooler with a full-cover block that transfers heat from the GPU, memory, and power stages to a custom liquid cooling loop.

Can I use either rear port as the inlet?

Yes. On the X-V2, either G1/4 port can serve as the inlet. Choose the direction that suits your tubing route.

Do I need a separate pump and radiator?

Yes. The block connects to a custom loop with a pump, reservoir, radiator, and tubing.

How do I check whether it fits my case?

Start with the block and backplate dimensions above. Check the space for fittings and tubing at the end of the card, and make sure the case has a suitable radiator mount.

Which thermal pads go on the card?

Use the supplied 1.2 mm pad strips at the memory and MOSFET contact areas identified by Bykski. The GPU die uses thermal paste.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.