Bykski · N-MS3090TRIO-TC-V2
GPU water block with an active backplate for MSI Gaming X Trio and Suprim X
The Bykski N-MS3090TRIO-TC-V2 is a full-cover water block for select MSI GeForce RTX 3090, 3080 Ti, and 3080 Gaming X Trio and Suprim X graphics cards. The front block cools the GPU, memory, and voltage regulators. The included bridge routes coolant through the active backplate in the same custom loop to cool rear memory on supported RTX 3090 cards.
Fits
Select MSI RTX 3090, 3080 Ti, and 3080 PCBs
Backplate
Active liquid cooling
Compatibility
This water block fits only the six MSI GeForce PCB layouts below.
- ✓MSI GeForce RTX 3090 SUPRIM X 24G
- ✓MSI GeForce RTX 3090 GAMING X TRIO 24G
- ✓MSI GeForce RTX 3080 Ti SUPRIM X 12G
- ✓MSI GeForce RTX 3080 Ti GAMING X TRIO 12G
- ✓MSI GeForce RTX 3080 SUPRIM X 10G
- ✓MSI GeForce RTX 3080 GAMING X TRIO 10G
Before ordering, confirm the exact model and memory capacity, then compare your card’s PCB layout with Bykski’s compatibility information.
MSI GeForce RTX 3090 SUPRIM X 24G with the stock cooler.
Design Highlights
Bykski coolant-flow illustration. Front block above, active backplate below.
Coolant flows through both sides
The front block and the active backplate each have a coolant channel. The backplate draws heat from the rear memory on supported RTX 3090 cards.
Jet microchannels over the GPU
The front cold plate uses jet microchannels with 0.3 mm spacing. The T2 copper plate also covers the front memory and power delivery contact areas.
Bykski illustration of the recommended bridge routing.
One bridge connects both blocks
The bridge links the front block and active backplate in series. Bykski shows the inlet below the outlet. Follow the IN and OUT markings when you connect the tubing.
Key Specifications
| Model | N-MS3090TRIO-TC-V2 |
|---|
| Front cold plate | Nickel-plated T2 high-purity copper |
|---|
| Front cover | Clear acrylic |
|---|
| Active backplate | Plated copper cold plate with a clear acrylic cover |
|---|
| Port thread | G1/4 |
|---|
| Front block with terminal (L × W × T) | 278.32 × 157.88 × 44.55 mm |
|---|
| Active backplate (L × W × T) | 295.00 × 127.85 × 17.00 mm |
|---|
| Thermal pads in Bykski’s mounting diagram | 1.5 mm |
|---|
| Lighting | 5V 3-pin addressable RGB (Bykski RBW) |
|---|
Bykski drawing in millimeters. Front block above, active backplate below.
Which Version Do I Need?
Start with the exact model on your card label, then choose the cooling layout you want.
Bykski N-MS3090TRIO-TC-V2THIS PAGE
Choose this for a listed PCB when you want coolant to flow through both the front block and the backplate.
Compare this front water block with a passive backplate if you only want liquid cooling on the front. Check its own PCB list.
Compare this water block for the MSI RTX 3090 VENTUS 3X 24G OC, MSI RTX 3080 VENTUS 3X 10G OC, or MSI RTX 3080 VENTUS 3X 12G OC. Check its PCB compatibility list before ordering.
Check this separate water block if you have an MSI RTX 3090 Ti GAMING X TRIO 24G.
What's in the Box
1 × full-cover GPU water block1 × active backplate1 × bridge module2× G1/4 stop plugsThermal padsMounting screws, washers, and bridge sealsARGB adapter cable
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Bykski view of the three main components.
Installation & Use
1Power off the system and remove the graphics card. Take off the stock cooler and backplate, clean away the old thermal material, and check that the mounting holes line up.
2Place thermal pads on the memory and power delivery contact points indicated for your PCB, including rear memory contact points where present. Apply your own thermal paste to the GPU die.
3Mount the front block and active backplate with the supplied mounting hardware. Seat the bridge seals before fastening the bridge to both blocks. Tighten the bridge screws just until snug.
4Connect your tubing with G1/4 fittings. Follow the bridge’s IN and OUT markings and seal the unused ports with the supplied plugs.
5For lighting, connect the adapter cable to a 5V 3-pin ARGB header or compatible 5V ARGB controller. Leak-test the loop before powering the graphics card.
You also need a pump, reservoir, radiator and fans, G1/4 tubing fittings, matching tubing, coolant, and thermal paste.
Bykski bridge installation drawing. Bridge seals (1), bridge module (2), mounting screws (3 and 4).
FAQ
Does this fit the MSI RTX 3090 SUPRIM X 24G?
Yes. Bykski lists the MSI GeForce RTX 3090 SUPRIM X 24G. Verify the PCB layout before ordering.
Does coolant flow through the backplate?
Yes. The included bridge connects the front block to the active backplate so both share the same coolant loop.
What fittings do I need?
Use G1/4 fittings that match your tubing. Use the included stop plugs to seal unused ports.
Can I connect the lighting to a 12V RGB header?
Use a 5V 3-pin ARGB header or a compatible 5V ARGB controller. A 12V 4-pin RGB header can damage the LEDs.
Notes- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.