RTX 4070 SUPER Water Block for ASUS Dual EVO 12GB, Bykski N-AS4070SDUALEVO-X

Bykski · N-AS4070SDUALEVO-X

Full-cover water block for the ASUS Dual RTX 4070 SUPER EVO

The Bykski N-AS4070SDUALEVO-X is a full-cover GPU water block for the ASUS Dual GeForce RTX 4070 SUPER EVO 12GB. It replaces the original cooler and transfers heat from the GPU core, memory, and power stages to a custom liquid cooling loop. It includes a passive aluminum backplate and connects to the loop through G1/4 ports.

Fits
ASUS Dual RTX 4070 SUPER EVO 12GB
Ports
G1/4
Lighting
5V ARGB (RBW)
Backplate
Passive aluminum

Compatibility

Match the exact card model and board layout.

  • ✓ASUS Dual GeForce RTX 4070 SUPER EVO 12GB (DUAL-RTX4070S-12G-EVO)

Not compatible:

  • ✗Other PCB layouts

Before ordering, compare your card’s PCB layout and mounting holes with the board diagram in Installation & Use.

ASUS product image of the DUAL-RTX4070S-12G-EVO with its stock cooler.

Design Highlights

One cold plate for the GPU, memory, and VRM

A T2 copper cold plate makes contact with the GPU core, memory, and voltage regulation components through their thermal interfaces. Coolant passes through 0.30 mm jet microchannels, visible through the clear acrylic top.

Passive aluminum backplate

The passive black aluminum backplate mounts behind the PCB. Coolant stays in the front block.

5V addressable RGB lighting

For motherboard control, connect the RBW lighting to a 5V 3-pin ARGB header through a compatible adapter. You can also use a compatible 5V RBW controller. Do not connect the lighting to a 12V 4-pin RGB header.

Key Specifications

ModelN-AS4070SDUALEVO-X
Cold plateT2 copper cold plate
TopClear PMMA acrylic
BackplatePassive black aluminum
Cooling coverageGPU core, memory, and VRM
Cold plate length145.46 mm
Copper plate thickness9 mm
Local copper base thickness0.35 mm (Bykski cross-section schematic)
Jet microchannels0.30 mm, up to 44 channels
Port threadG1/4 inlet and outlet
Water block (L × W × T)189.87 × 146.01 × 26.25 mm
Backplate (L × W × T)189.87 × 116.01 × 6.00 mm
Lighting5V ARGB (RBW). Motherboard connection via adapter to a 5V 3-pin ARGB header.

Bykski dimension drawing. Water block above, backplate below. Measurements are in millimeters.

Which Version Do I Need?

Use the full ASUS model name to find the block for your PCB.

N-AS4070SDUALEVO-XTHIS PAGE
Choose this block for the listed ASUS Dual RTX 4070 SUPER EVO 12GB. Verify your board against the installation diagram.
Check this block if you have the ASUS TUF Gaming GeForce RTX 4070 SUPER OC.
Check this block if you have the ASUS ROG Strix GeForce RTX 4070 SUPER O12G Gaming.

What's in the Box

1 × Full-cover GPU water block1 × Backplate2 × G1/4 stop plugsThermal padsMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski assembly drawing. 1 Block · 2 Thermal pads · 3 Your graphics card PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws.

Installation & Use

1
Remove the original cooler and backplate, then clean off old paste and pad residue.
2
Cut and place the supplied thermal pads on the memory and VRM contact areas shown in the diagram. Apply your own thermal paste to the GPU die.
3
Line up the block and backplate with the PCB mounting holes. Fit the washers and screws as shown in Bykski’s assembly diagram and tighten evenly. Stop if the block does not seat correctly.
4
Connect the loop with G1/4 fittings, following the inlet and outlet marks. Seal unused ports with the stop plugs.
5
Leak-test the loop before powering the graphics card.

You also need a pump, radiator, G1/4 tubing fittings, tubing, coolant, and your own thermal paste.

Bykski PCB diagram. The shaded areas around the central die show pad locations. The syringe marks where to apply paste.

FAQ

Will this fit my RTX 4070 SUPER?

Check that the card is the ASUS Dual GeForce RTX 4070 SUPER EVO 12GB (DUAL-RTX4070S-12G-EVO). Match the PCB and mounting holes before ordering.

Can I use it as an all-in-one (AIO) GPU cooler?

This block goes into a custom liquid cooling loop. It requires a separate pump, radiator, fittings, tubing, and coolant.

What fittings do I need?

Use G1/4 fittings for the inlet and outlet. Use the included stop plugs to close the unused ports.

How do I connect the RBW lighting?

Use a compatible adapter to connect it to a 5V 3-pin ARGB motherboard header, or use a compatible 5V RBW controller. A 12V 4-pin RGB header can damage the lighting.

Where do the thermal pads go?

Place the supplied thermal pads on the memory and VRM contact areas shown in the installation diagram. Apply your own thermal paste to the GPU die.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.