Leadtek RTX A2000 Full-Cover Water Block with Backplate | Bykski N-RTXA2000-X-V2

Bykski · N-RTXA2000-X-V2

Full-cover water block for the Leadtek RTX A2000

The Bykski N-RTXA2000-X-V2 is a full-cover water block with an aluminum backplate for the Leadtek NVIDIA RTX A2000 PCB shown below. It replaces the card's factory fan cooler. The copper cold plate transfers heat from the GPU, memory, and power delivery components into a custom liquid cooling loop.

Fits
Leadtek RTX A2000
Cold plate
T2 copper
Ports
2 × G1/4
Backplate
Aluminum

Compatibility

Fits the board shown here

  • ✓Leadtek NVIDIA RTX A2000 (Ampere), with the pictured PCB layout

Not compatible:

  • ✗RTX A2000 cards with a different PCB layout

Before ordering, compare your bare PCB's mounting holes and component placement with the board drawing and the PCB photo in the product gallery.

Leadtek card with its factory cooler above the Bykski PCB drawing.

Design Highlights

One cold plate for the GPU, memory, and power stages

The raised surfaces on the T2 copper cold plate line up with the GPU and the components it cools. The block mounts with a stainless steel panel and a separate aluminum backplate.

Two side ports for flexible tube routing

The two G1/4 ports sit side by side in a black POM terminal. Use either port as the inlet to suit your tubing route.

0.5 mm microchannel spacing

Coolant runs through channels in the cold plate to carry heat into the loop. Bykski lists the thermal conductivity of the T2 copper at 401 W/(m·K).

Key Specifications

ModelN-RTXA2000-X-V2
TypeFull-cover GPU water block for a custom loop
Cold plateT2 high-purity copper
Top panelStainless steel
Side terminalBlack POM
Port thread2 × G1/4
Block dimensions151.04 × 79.97 × 22.80 mm
Backplate materialAluminum
Backplate dimensions166.53 × 54.11 × 5.96 mm
Thermal pad thickness1.5 mm

Manufacturer drawing of the block. Dimensions in millimeters.

Which Version Do I Need?

Check the model printed on your card. NVIDIA RTX 2000 Ada Generation is a different GPU model with a similar name.

Bykski N-RTXA2000-X-V2THIS PAGE
Choose this block if your Leadtek RTX A2000 matches the PCB shown above and you have a custom loop or plan to build one.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate6 × 1.5 mm thermal pads4 × 0.5 mm insulating washers4 × spring screws4 × backplate screws

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Shut down and unplug the system. Remove the graphics card and its factory cooler, then clean off the old thermal paste and pads.
2
Check that the mounting holes line up. Cut the 1.5 mm pads to fit the memory and MOSFET contact areas. Leave the inductors bare and apply your own GPU thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Place the four insulating washers at the holes around the GPU, then tighten the spring screws gradually in a cross pattern. Fit the remaining backplate screws.
4
Connect the block to your loop with G1/4 fittings and fill the loop with coolant.
5
Run only the pump and check each connection for leaks before powering the graphics card.

You also need a pump and reservoir (separate or combined), a radiator with fans, G1/4 fittings matched to your tubing, tubing, and coolant.

1 Water block · 2 Thermal pads · 3 Graphics card PCB · 4 Insulating washers · 5 Spring screws · 6 Backplate · 7 Backplate screws

FAQ

How can I tell if the block fits my RTX A2000?

Match the mounting holes and component layout of your bare Leadtek PCB to the reference above before ordering.

Do I need a separate pump and radiator?

Yes. The block connects to a custom loop with a pump, reservoir, radiator, fans, tubing, fittings, and coolant.

Which port should I use as the inlet?

Either side port can serve as the inlet. Both take G1/4 fittings.

Where do the thermal pads go?

Use the 1.5 mm pads on the memory and MOSFETs where they meet the cold plate. Leave the inductors uncovered.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.