NVIDIA A30X 24GB Full-Cover GPU Water Block with Backplate | Bykski N-TESLA-A30X-24G-SR

€176.91 piece
items available
View Details
Bykski · N-TESLA-A30X-24G-SR

Full-cover water block for the NVIDIA A30X 24GB

The Bykski N-TESLA-A30X-24G-SR is a full-cover GPU water block with an aluminum backplate for the NVIDIA A30X 24GB PCIe accelerator. It replaces the card’s stock passive heatsink and transfers heat from the card into a custom liquid cooling loop. The nickel-plated T2 copper cold plate has raised contact surfaces across the PCB, and G1/4 ports connect the block to the loop.

Fits
NVIDIA A30X 24GB
Cooling
Custom loop
Cold plate
Nickel-plated T2 copper
Ports
G1/4

Compatibility

Supported board layout

  • ✓NVIDIA A30X 24GB (PCIe Gen4, full-height, full-length)

Compare the PCB layout and mounting holes with the photo before ordering.

NVIDIA A30X 24GB bare PCB (manufacturer reference).

Design Highlights

Copper contact across the board

The 228.5 mm T2 copper cold plate has raised contact surfaces for the card’s heat-producing components. A nickel finish protects the copper surface. The separate aluminum backplate sits outside the coolant path.

0.3 mm jet microchannels

Coolant passes through a jet microchannel section with up to 44 channels. The narrow channels increase the surface area in contact with the coolant.

Manufacturer illustration of the coolant channels.

Two ports at one end

Both ports use G1/4 female threads.

Key Specifications

ModelN-TESLA-A30X-24G-SR
Cold plateNickel-plated T2 copper
Copper material conductivity401 W/(m·K)
Panel304 stainless steel
BackplateBlack aluminum
Block dimensions (L × W × T)Approx. 267.5 × 99.8 × 27.3 mm
Backplate dimensions (L × W × T)Approx. 249.8 × 95.1 × 5.0 mm
Net weight1.3 kg
Port threadsG1/4 female
SealEPDM
Maximum working pressure2 bar
Block temperature range−20 to 60°C
Fluids listed for the blockWater, ethylene glycol, propylene glycol, fluorinated fluid, or mineral oil. Check compatibility with every component in your loop.

Manufacturer dimensions in mm. Water block above, backplate below.

Which Version Do I Need?

Both cooling options are designed for the A30X 24GB board shown above.

N-TESLA-A30X-24G-SRTHIS PAGE
Choose this block and backplate to add the A30X to an existing or planned custom loop.
Choose this A30X AIO if you want the GPU block, inline pump, and 360 mm radiator with fans in one kit. Select “360mm” on the linked product page.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate5 × 1.5 mm thermal pad stripsSpring screwsM2 × 9.5 mm backplate screwsInsulating washers

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Power down the system, remove the card, and lift off the stock heatsink. Clean away the old paste and pad residue.
2
Check that the block and backplate align with the PCB mounting holes before applying thermal materials.
3
Cut the 1.5 mm thermal pads to fit the red areas in the installation diagram. Apply your own GPU thermal paste to the GPU die outlined in blue.
4
Fit the block and backplate. Use the insulating washers at the corresponding holes, then tighten the spring screws and backplate screws evenly.
5
Connect the loop with G1/4 fittings and fill it. Run the pump with the rest of the system powered off and finish leak testing before powering the card.

You also need a pump and reservoir, a radiator and fans, G1/4 fittings matched to your tubing, tubing, and coolant.

Red marks the thermal pad locations. Blue outlines the GPU die for thermal paste.

FAQ

What cooling does the NVIDIA A30X use from the factory?

The stock A30X is a passively cooled PCIe card rated for up to 230 W. This block replaces its passive heatsink for use in a custom liquid cooling loop.

Will the block fit a standard NVIDIA A30 24GB?

Bykski lists the A30X PCB only. The NVIDIA A30 is a separate accelerator model, so check the full model name and PCB before ordering.

Do I need a separate pump and radiator?

Yes. The water block connects to a custom cooling loop with its own pump, reservoir, radiator, and fans.

What thermal pad thickness does Bykski specify?

Use 1.5 mm thermal pads cut to fit the red areas in the installation diagram. Apply your own GPU thermal paste to the GPU die outlined in blue.

How can I check clearance in my chassis?

The block measures about 267.5 × 99.8 × 27.3 mm. Use the dimension drawing and allow space for the fittings and tubing at the end of the card.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.