Sapphire RX 7900 XTX NITRO+ GPU Water Block, Bykski A-SP7900XTX-X

Bykski · A-SP7900XTX-X

Full-cover GPU water block for Sapphire Radeon RX 7900 XTX NITRO+ and select PULSE cards

The Bykski A-SP7900XTX-X is a full-cover water block for the Sapphire Radeon RX 7900 XTX NITRO+ Vapor-X and the specific PULSE boards listed below. It replaces the stock cooler and uses a copper cold plate to transfer heat from the GPU, memory, and power stages to a custom liquid cooling loop.

Fits
Sapphire RX 7900 XTX NITRO+ and listed PULSE boards
Cold plate
T2 copper
Port thread
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists these Sapphire Radeon PCB layouts.

  • ✓Sapphire Radeon RX 7900 XTX NITRO+ Vapor-X 24GB (11322-01-40G)
  • ✓Sapphire Radeon RX 7900 XTX PULSE 24GB (11322-02-20G)
  • ✓Sapphire Radeon RX 7900 XT PULSE 20GB (11323-02-20G)
  • ✓Sapphire Radeon RX 7900 XT PULSE Platinum OC 20GB (SKU prefix 11323-04)

Before ordering, check the exact model on your card label. Confirm that the mounting holes and component contact points on that model’s PCB match the block.

Sapphire Radeon RX 7900 XTX NITRO+ Vapor-X with its factory cooler.

Design Highlights

Bykski illustration of the coolant path.

Cooling across the GPU, memory, and VRM

The copper cold plate takes heat from the GPU die, memory modules, and voltage regulators. Coolant passes through the jet microchannels and carries the heat into the loop.

Aluminum backplate

The included backplate mounts behind the PCB and supports the board. Coolant runs through the block on the front of the card.

5V addressable lighting

The clear acrylic top shows the coolant channels and the light from the included ARGB strip. For motherboard sync, use a matching 5V ARGB adapter cable to connect the strip to a 5V 3-pin ARGB header. You can also use a compatible 5V ARGB controller.

Key Specifications

ModelA-SP7900XTX-X
Cold plateT2 copper
TopClear acrylic
BackplateBlack aluminum
Inlet and outlet threadG1/4
Block (L × W × T)276.70 × 147.82 × 23.05 mm
Backplate (L × W × T)276.70 × 117.15 × 6.00 mm
Lighting5V addressable RGB (RBW)

Bykski dimension drawing in millimeters. Backplate above, water block below.

Which Version Do I Need?

Match the block to the exact graphics card and PCB you own.

Bykski A-SP7900XTX-XTHIS PAGE
Choose this block for a Sapphire card in the compatibility list with a matching PCB.
For the ASUS TUF Gaming Radeon RX 7900 XTX OC or RX 7900 XT OC. Check your PCB against that listing before ordering.
Check this block and its PCB photo if you have an AMD Radeon RX 7900 XT reference card.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB LED strip

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system, take out the graphics card, and remove the factory cooler. Clean off the old thermal pads and paste.
2
Use Bykski’s pad placement diagram and the contact areas on your block to place the supplied thermal pads on the memory and power stages. Apply a thin, even layer of your own thermal paste to the GPU die.
3
Align the water block and backplate with the PCB mounting holes. Use the supplied hardware and tighten evenly. If the mounting points do not line up, stop and recheck the PCB layout.
4
Connect the loop to the marked inlet and outlet with G1/4 fittings. Seal the unused ports with the stop plugs.
5
Leak-test the loop while the graphics card is unpowered.

You also need a pump, radiator, reservoir, G1/4 fittings, tubing, and coolant.

FAQ

Does this water block fit the Sapphire RX 7900 XTX PULSE?

Bykski lists the Sapphire Radeon RX 7900 XTX PULSE 24GB (11322-02-20G). Confirm that the mounting holes and component contact points on your card’s PCB match the block.

Which Sapphire RX 7900 XT PULSE boards fit?

Bykski lists the RX 7900 XT PULSE 20GB and the RX 7900 XT PULSE Platinum OC 20GB. Check your card’s model label and PCB layout.

Is this a complete water cooling kit?

This is a GPU block and backplate for a custom loop. You need a pump, radiator, reservoir, fittings, tubing, and coolant.

Which fittings do I need?

Use G1/4 fittings for the inlet and outlet, then close the unused ports with the supplied stop plugs.

How do I connect the 5V ARGB lighting?

Use a matching 5V ARGB adapter cable to connect the strip to a 5V 3-pin motherboard ARGB header, or use a compatible 5V ARGB controller. A 12V 4-pin RGB header will damage the strip.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.