Bykski · N-MS3090TRIO-X
Full-cover GPU water block for MSI RTX 3080 and 3090
The Bykski N-MS3090TRIO-X replaces the stock cooler on select MSI GeForce RTX 3080 and RTX 3090 GAMING X TRIO and SUPRIM X cards. Its copper cold plate transfers heat from the GPU core, memory, and power delivery components to a custom liquid cooling loop. It includes a passive aluminum backplate.
Fits
Select MSI GAMING X TRIO and SUPRIM X PCBs
Backplate
Passive aluminum
Compatibility
This block fits the specified PCB layouts of these MSI cards.
- ✓MSI GeForce RTX 3080 GAMING X TRIO 10G
- ✓MSI GeForce RTX 3080 SUPRIM X 10G
- ✓MSI GeForce RTX 3090 GAMING X TRIO 24G
- ✓MSI GeForce RTX 3090 SUPRIM X 24G
Not compatible:
- ✗MSI GeForce RTX 3090 VENTUS 3X 24G OC
- ✗MSI GeForce RTX 3090 Ti GAMING X TRIO 24G
- ✗MSI GeForce RTX 3090 Ti SUPRIM X 24G
Before ordering, verify the full model on your card and check that the PCB layout matches the one specified for that model.
MSI GeForce RTX 3090 GAMING X TRIO 24G shown with its stock cooler.
Design Highlights
Bykski coolant flow schematic. Check the PCB layout specified for your card before installation.
One cold plate for the GPU, memory, and VRM
The copper plate contacts the GPU core and uses thermal pads at the specified memory and voltage regulator contact points. Coolant carries heat away from the plate.
The jet microchannels sit beneath the clear acrylic top.
5V addressable lighting
Run the RBW light strip from a compatible 5V ARGB controller or a 5V 3-pin motherboard header with the appropriate adapter. Keep the strip off 12V RGB headers.
Key Specifications
| Model | N-MS3090TRIO-X |
|---|
| Cold plate | Copper |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Black aluminum, passive |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Port thread | G1/4 |
|---|
| Water block (L × W × T) | 278.3 × 157.9 × 23.5 mm |
|---|
| Lighting | 5V 3-pin ARGB (RBW) |
|---|
Bykski water block drawing. Measurements are in millimeters.
Which Version Do I Need?
Match your card’s exact model and PCB before choosing a block.
Bykski N-MS3090TRIO-XTHIS PAGE
Choose this block for a listed GAMING X TRIO or SUPRIM X PCB if you want a passive rear plate.
Choose this version if you want coolant to flow through the rear plate. Check its own PCB compatibility list.
Check this block for the MSI RTX 3090 VENTUS 3X 24G OC.
Check this block for the MSI RTX 3090 Ti GAMING X TRIO 24G or SUPRIM X 24G.
What's in the Box
1 × full-cover GPU water block with 5V 3-pin ARGB lighting1 × passive backplate2× G1/4 stop plugsMounting hardware setThermal pads
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Included passive backplate.
Installation & Use
1Power off the PC and remove the graphics card. Remove the stock cooler and backplate, then clean off the old thermal paste and pads.
2Check that the block lines up with the PCB and its screw holes. Fit the thermal pads to the memory and VRM contact areas specified for your PCB. Apply a thin layer of your own thermal paste to the GPU die.
3Use the mounting hardware to secure the water block and backplate. Tighten the screws evenly and avoid forcing the block into place.
4Connect the tubing with G1/4 fittings and close unused ports with the stop plugs. If you use the lighting, connect it to a compatible 5V ARGB source.
5Fill and bleed the loop. Leak-test it with only the pump powered before turning on the graphics card.
You’ll also need a pump, radiator, G1/4 fittings, tubing, and coolant.
FAQ
Will this water block fit my MSI RTX 3080?
Check the card label for GAMING X TRIO 10G or SUPRIM X 10G. The RTX 3090 photo in Compatibility shows the exterior with its stock cooler. Before ordering, match your card’s actual PCB to the layout specified for its model.
Is this a complete RTX 3090 water cooling kit?
It’s the GPU block and backplate for a custom loop. A complete loop also needs a pump, radiator, G1/4 fittings, tubing, and coolant.
Does coolant flow through the included backplate?
The included aluminum backplate is passive. Coolant flows through the front block.
Which fittings do I need for the block?
Use G1/4 fittings that match your tubing. Use the supplied stop plugs to close unused ports.
Can I plug the lighting into a 12V RGB header?
Use a compatible 5V ARGB controller or a 5V 3-pin ARGB header with the appropriate adapter. A 12V RGB header can damage the light strip.