ZOTAC RTX 3090 / 3080 Water Block with Backplate, Bykski N-ST3090XG-X-V2

Bykski · N-ST3090XG-X-V2

Full-cover water block for select ZOTAC GeForce RTX cards

The Bykski N-ST3090XG-X-V2 replaces the stock cooler on select ZOTAC cards, including the GeForce RTX 3090 Trinity OC and RTX 3080 Trinity OC with a matching dual 8-pin short PCB. Its nickel-plated copper cold plate transfers heat from the GPU, memory, and voltage regulators to a custom liquid cooling loop. A passive aluminum backplate mounts behind the card.

Fits
Listed ZOTAC short PCBs
Backplate
Passive aluminum
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Fits the following ZOTAC GeForce cards with the matching short PCB and two 8-pin PCIe power sockets.

  • ✓ZOTAC GeForce RTX 3090-24G6X X-GAMING OC
  • ✓ZOTAC GeForce RTX 3090 Trinity (ZT-A30900D-10P)
  • ✓ZOTAC GeForce RTX 3090 Trinity OC (ZT-A30900J-10P)
  • ✓ZOTAC GeForce RTX 3080 Ti-12G6X X-GAMING OC
  • ✓ZOTAC GeForce RTX 3080 Ti AMP Holo (ZT-A30810F-10P)
  • ✓ZOTAC GeForce RTX 3080 Ti Trinity OC (ZT-A30810J-10P)
  • ✓ZOTAC GeForce RTX 3080-10G6X X-GAMING OC
  • ✓ZOTAC GeForce RTX 3080 Trinity 10GB (ZT-A30800D-10P)
  • ✓ZOTAC GeForce RTX 3080 Trinity OC 10GB (ZT-A30800J-10P)
  • ✓ZOTAC GeForce RTX 3080 AMP Holo 10GB (ZT-A30800F-10P)
  • ✓ZOTAC GeForce RTX 3070 Ti-8G6X X-GAMING GOC

Not compatible:

  • ✗ZOTAC GeForce RTX 3090 AMP Extreme Holo (ZT-A30900B-10P, three 8-pin sockets)
  • ✗ZOTAC GeForce RTX 3090 AMP Core Holo (ZT-A30900C-10P, three 8-pin sockets)
  • ✗ZOTAC GeForce RTX 3090 Ti AMP Extreme Holo (ZT-A30910B-10P, 12+4-pin socket)

Bykski’s compatibility chart also uses the label “RTX 3080 Ti AMP HoloBlack.” If your card is described that way, verify the exact model code and board layout.

Before ordering, confirm the exact model on your card label and compare the entire PCB with the diagram. Check the mounting holes, board outline, and power socket positions.

Bykski’s front PCB diagram. The two PCIe 8-pin sockets are at the upper right.

Design Highlights

Microchannels in the copper cold plate

The copper plate contacts the GPU core, memory, and power delivery components. Jet microchannels route coolant through the plate over the GPU.

Bykski exploded view of the block and backplate installation.

Front block and passive backplate

The cold plate and backplate mount on opposite sides of the PCB. Coolant runs through the front block, and the aluminum backplate contacts the marked rear components through thermal pads.

Key Specifications

ModelN-ST3090XG-X-V2
Cold plateNickel-plated T2 copper
TopClear acrylic
BackplateBlack aluminum, passive
Cooling coverageGPU core, memory, and voltage regulators
Inlet / outlet threadG1/4
Lighting5V 3-pin addressable RGB (RBW)

Which Version Do I Need?

Choose by how you want to cool the back of the PCB, then verify your card against the listing for that block.

Bykski N-ST3090XG-X-V2THIS PAGE
Choose this version for a front water block with a passive aluminum backplate.
Choose this version if you want coolant to flow through both the front block and the active backplate. A bridge connects the two.

What's in the Box

1 × full-cover GPU water block1 × passive aluminum backplate5 × thermal pad strips4 × 0.5 mm insulating washers4 × spring screws6 × M2 × 9.5 mm backplate screwsOther mounting hardware2× G1/4 stop plugsLighting adapter cableInstallation instructions

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Included passive aluminum backplate.

Installation & Use

1
Power off the system. Remove the card and its stock cooler, then clean off the old pads and paste.
2
Check that the mounting holes and contact surfaces line up. Use the pads specified for your kit on the marked memory and power delivery areas. Apply your own thermal paste to the GPU die.
3
Align the block and backplate with the PCB and tighten the mounting screws gradually in a cross pattern. If the assembly does not sit flat, stop and check the pad and hardware placement.
4
Connect the tubing with G1/4 fittings at the marked inlet and outlet. Fill and bleed the loop, then leak-test it before powering the card.

You also need a pump, radiator, tubing, coolant, and G1/4 fittings.

FAQ

Will it fit my ZOTAC RTX 3080 Trinity?

The 10GB Trinity (ZT-A30800D-10P) and Trinity OC (ZT-A30800J-10P) are listed for the matching short PCB with two 8-pin power sockets. Verify the model code and compare the board before ordering.

Will it fit the ZOTAC RTX 3090 Ti AMP Extreme Holo?

The ZT-A30910B-10P has a 12+4-pin socket. The block requires the listed short PCB with two 8-pin sockets.

What else do I need for RTX 3090 water cooling?

This block connects to a custom loop with a pump, radiator, tubing, coolant, and G1/4 fittings.

Which header does the lighting use?

Use a compatible 5V three-pin ARGB header with the lighting adapter cable. Keep the RBW lighting disconnected from 12V four-pin RGB.

Does coolant flow through the included backplate?

Coolant flows through the front block. The included backplate is passive aluminum.

Notes
  • If you have any questions, don't hesitate to contact support for confirmation.