Bykski · IC-BIV150-SR
Full-cover water block for TianGai 150
The Bykski IC-BIV150-SR is a full-cover GPU water block for the Iluvatar CoreX TianGai 150 (BI-V150) 64GB PCIe accelerator. It replaces the factory passive heatsink and transfers heat from the card to coolant in a custom loop. The all-metal block comes with a separate aluminum backplate and connects through G1/4 ports.
Fits
TianGai 150 (BI-V150)
Cold plate
Nickel-plated T2 copper
Backplate
Aluminum, included
Compatibility
Bykski lists the BIV150 board layout shown here.
- ✓Iluvatar CoreX TianGai 150 (BI-V150), 64GB HBM2e PCIe
Before ordering, compare your card’s PCB, mounting holes, and component layout with the reference photo.
Bykski’s reference photo of the BIV150 PCB.
Design Highlights
Bykski’s cold plate illustration.
Coolant through the copper cold plate
Coolant passes through 0.3 mm jet microchannels in the nickel-plated copper cold plate before carrying heat away to your loop’s radiator.
Separate aluminum backplate
The aluminum backplate screws onto the rear of the PCB. It mounts opposite the water block, with the card between the two parts.
Key Specifications
| Model | Bykski IC-BIV150-SR |
|---|
| Block materials | Copper and 304 stainless steel |
|---|
| Cold plate | Nickel-plated T2 copper |
|---|
| Copper plate length | 222.18 mm |
|---|
| Backplate | Aluminum |
|---|
| Port threads | G1/4 female |
|---|
| Block dimensions | 278.19 × 106.68 × 16.60 mm |
|---|
| Backplate dimensions | 266.63 × 106.70 × 4.00 mm |
|---|
| Net weight | 1.4 kg |
|---|
| Maximum working pressure | 4 bar |
|---|
| Working temperature | −20 to 60 °C |
|---|
| Seal material | EPDM |
|---|
The block is shown above the backplate. Dimensions are in millimeters.
Which Version Do I Need?
Choose based on how you want to set up liquid cooling for your TianGai 150.
Bykski IC-BIV150-SRTHIS PAGE
Choose this block and backplate if you’re building a custom loop or adding the card to one you already have.
Choose the all-in-one kit if you want the block, pump, tubing, and fan-equipped radiator in one assembly.
What's in the Box
1 × IC-BIV150-SR water block1 × aluminum backplate2 × 1.5 mm thermal pad strips8 × 0.5 mm insulating washers8 × M2 × 5 mm spring screws6 × backplate screws
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
Installation & Use
1Remove the factory heatsink and clean the old thermal material from the card.
2Fit the 1.5 mm pads to the MOSFET locations shown. Apply a thin layer of your own GPU thermal paste to the marked chip contact surfaces.
3Align the block with the PCB holes and position the backplate on the rear. Fit the insulating washers and spring screws at the matching holes, then secure the backplate with its own screws. Tighten evenly and stop if the block does not sit flush.
4Connect the block to the loop with G1/4 fittings and fill the reservoir. Power only the pump to circulate coolant, bleed air, and check for leaks. Keep the GPU and the rest of the system powered off during the test.
You’ll also need a pump, reservoir, radiator with fans, G1/4 fittings, matching tubing, and coolant compatible with your loop.
The dark strips mark the thermal pad locations. The syringe symbols mark where to apply paste.
FAQ
How is the BI-V150 cooled from the factory?
Its original heatsink is passive and relies on airflow from the server’s chassis fans. Iluvatar rates the card at 350 W of board power.
Do I need a separate pump and radiator?
Yes. The IC-BIV150-SR connects to a custom loop, so you’ll need a pump and a radiator with fans.
What thermal pad thickness should I use?
Bykski specifies 1.5 mm pads for the MOSFET positions in the installation diagram.
How do I check clearance in my case?
The original BI-V150 is a full-length, full-height, dual-slot PCIe card. Use the block and backplate dimensions above to check clearances, allowing space for the fittings, tubing, and radiator.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.