Bykski · N-EV3090FTW3-TC-V2
EVGA FTW3 Ultra Gaming water block with active backplate
The Bykski N-EV3090FTW3-TC-V2 replaces the stock cooler on supported EVGA GeForce RTX 3090 FTW3 Ultra Gaming cards. The full-cover front block cools the GPU, memory, and voltage regulators. A coolant-fed backplate cools the RTX 3090’s rear memory, and the included bridge links both plates to the same custom loop.
Fits
Select EVGA FTW3 Ultra Gaming PCBs
Compatibility
Confirmed EVGA FTW3 Ultra Gaming PCB layouts
- ✓EVGA GeForce RTX 3090 FTW3 Ultra Gaming 24GB (24G-P5-3987-KR)
- ✓EVGA GeForce RTX 3080 Ti FTW3 Ultra Gaming 12GB
Not compatible:
- ✗EVGA GeForce RTX 3090 Ti FTW3 Ultra Gaming
Bykski also lists the EVGA GeForce RTX 3080 FTW3 Ultra Gaming by name. Ask support to confirm your exact 3080 part number and PCB.
Before ordering, check your exact card part number and compare its full PCB layout and revision with Bykski’s compatibility information.
Bare PCB from EVGA’s RTX 3090 and RTX 3080 FTW3 cooler guide. Check the layout for your exact card.
Design Highlights
Full-cover front block
Jet microchannels carry coolant across the GPU contact area. The same cold plate draws heat from the front memory and voltage regulators through thermal pads.
Bykski’s illustration of the rear coolant chamber.
Coolant flow behind the PCB
The active backplate has its own coolant channel to draw heat from the RTX 3090’s rear memory. The bridge links the backplate to the front block so both run in the same loop.
Key Specifications
| Manufacturer model | N-EV3090FTW3-TC-V2 |
|---|
| Front cold plate and active backplate | Electroplated copper with clear acrylic covers |
|---|
| Front block with bridge (L × H × D) | 288.79 × 154.62 × 47.05 mm |
|---|
| Active backplate (L × H × D) | 288.87 × 124.61 × 17.15 mm |
|---|
| Inlet and outlet thread | G1/4 |
|---|
| Lighting connector | 5V 3-pin addressable RGB (RBW) |
|---|
Bykski drawing. Front block with bridge above, active backplate below. Dimensions are in millimeters.
Which Version Do I Need?
N-EV3090FTW3-TC-V2THIS PAGE
Choose this kit for a supported FTW3 Ultra Gaming PCB when you want coolant flowing through the front block and rear plate.
Choose this version for front-side liquid cooling with a passive backplate. Check its own PCB compatibility list.
Check this separate block if your card is an EVGA GeForce RTX 3090 Ti FTW3 Ultra Gaming.
What's in the Box
1 × Full-cover GPU water block1 × Active backplate1 × Coolant bridgeMounting hardwareThermal padsSealing rings2× G1/4 stop plugs5V ARGB lighting
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Front block, active backplate, and coolant bridge.
Installation & Use
1Shut down the PC and remove the graphics card. Remove the stock cooler, clean off the old thermal materials, and check that the block’s mounting holes line up with the PCB.
2Place thermal pads on the designated memory and voltage regulator contact points. Follow the pad layout for your PCB, including rear memory where present. Apply your own thermal paste to the GPU die.
3Align the front block, PCB, and backplate. Place the insulating washers at the GPU mounting holes as shown in Bykski’s installation guide. Tighten the GPU spring screws evenly in a diagonal pattern, then secure the remaining backplate screws.
4Seat the sealing rings and secure the bridge to both plates without overtightening. Connect G1/4 fittings at the marked inlet and outlet and seal unused ports with stop plugs.
5Connect the lighting to a compatible 5V 3-pin ARGB header. Leak-test the loop before powering the graphics card.
You also need a pump, radiator, G1/4 loop fittings, tubing, and coolant.
Bridge installation. 1 marks the sealing rings, 2 the bridge, and 3 and 4 the fasteners.
FAQ
How do I check fit on an EVGA RTX 3080 FTW3 Ultra Gaming?
Bykski’s V2 chart lists this model by name. Have support confirm the exact EVGA part number and PCB layout before ordering.
Will this fit an EVGA RTX 3090 Ti FTW3 Ultra Gaming?
The RTX 3090 Ti FTW3 Ultra Gaming requires its own water block. Bykski lists the N-EV3090TIFTW3-X for that card.
Does coolant circulate through the backplate?
Yes. The included bridge routes coolant through the front block and the active backplate in the same loop.
What fittings and RGB header should I use?
Use G1/4 loop fittings and a 5V 3-pin ARGB header for the lighting. A 12V 4-pin RGB header can damage the LEDs.
Notes- This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
- Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item.
- Product does NOT come with English instructions.
- Not responsible for any damage caused by or when using this product. Please use at your own risk.
- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.