Gigabyte RTX 4070 Ti / RTX 4070 Full-Cover Water Block with Backplate | Bykski N-GV4070TIAROC-X

Bykski · N-GV4070TIAROC-X

Full-cover GPU water block for select Gigabyte RTX 4070 cards

The Bykski N-GV4070TIAROC-X is a full-cover GPU water block for select Gigabyte cards, including the GeForce RTX 4070 Ti GAMING OC 12G. It replaces the stock cooler and uses a copper cold plate to transfer heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop.

Fits
Select Gigabyte RTX 4070 Ti, 4070 and 4070 SUPER
Cold plate
Copper
Port thread
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists these Gigabyte models for the PCB layouts shown in its fitment chart.

  • ✓GeForce RTX 4070 Ti AERO OC 12G
    GV-N407TAERO OC-12GD
  • ✓GeForce RTX 4070 Ti GAMING OC 12G
    GV-N407TGAMING OC-12GD
  • ✓GeForce RTX 4070 Ti WINDFORCE OC 12G
    GV-N407TWF3OC-12GD
  • ✓GeForce RTX 4070 GAMING OC 12G
    GV-N4070GAMING OC-12GD
  • ✓GeForce RTX 4070 WINDFORCE OC 12G
    GV-N4070WF3OC-12GD
  • ✓GeForce RTX 4070 EAGLE OC 12G
    GV-N4070EAGLE OC-12GD
  • ✓AORUS GeForce RTX 4070 SUPER MASTER 12G
    GV-N407SAORUS M-12GD

Before ordering, verify your card’s full model number and PCB revision. Ask FormulaMod to confirm the board layout if you’re unsure.

Gigabyte GeForce RTX 4070 Ti GAMING OC 12G shown with its stock cooler.

Design Highlights

One cold plate for the core, memory, and VRM

The machined contact surfaces align with the GPU core, memory modules, and voltage regulators on the supported PCB layouts.

Jet microchannels over the GPU

Coolant passes through the fin array in the center of the cold plate. The clear acrylic top shows the channel layout.

Passive aluminum backplate

The included black backplate mounts behind the PCB, outside the coolant path.

Key Specifications

Model (SKU)N-GV4070TIAROC-X
Cold plateCopper
TopClear acrylic (PMMA)
BackplateBlack aluminum, passive
Port threadG1/4 inlet and outlet
Lighting5V 3-pin addressable RGB (ARGB / RBW)
Block length175.49 mm
Block thickness26.25 mm
Backplate (L × W × T)175.49 × 117.90 × 6.00 mm

Bykski drawing in millimeters. Water block above, backplate below.

Which Version Do I Need?

Match the block to the card manufacturer and the full model name on your card label.

Bykski N-GV4070TIAROC-XTHIS PAGE
Choose this block for a matching Gigabyte PCB in the compatibility list above.
Choose this block for the PNY GeForce RTX 4070 12GB Gaming VERTO.

What's in the Box

1 × full-cover GPU water block1 × black aluminum backplate2 × G1/4 stop plugs1 × 5V ARGB light stripThermal pad setMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski assembly drawing. ① water block · ② thermal pads · ③ your graphics card PCB · ④ spacers · ⑤ spring screws · ⑥ backplate · ⑦ backplate screws.

Installation & Use

1
Shut down and unplug the PC. Remove the graphics card, then detach its stock cooler and backplate. Clean off the old thermal materials.
2
Place the thermal pads where the cold plate contacts the memory and power components, following Bykski’s placement diagram. Apply your own thermal paste to the GPU die.
3
Align the block and backplate with the PCB mounting holes. Fit the spacers and tighten the mounting screws evenly.
4
Attach your G1/4 fittings to the marked inlet and outlet, and close the unused ports with the supplied stop plugs. Connect the lighting to a 5V 3-pin ARGB header.
5
Fill and leak-test the loop with the graphics card unpowered before starting the PC.

For a new loop, you’ll also need a pump, reservoir, radiator, tubing, G1/4 fittings sized for your tubing, and coolant.

Bykski placement example. Pads go on the shaded memory and power components. The syringe marks the GPU die.

FAQ

Does this fit the Gigabyte RTX 4070 Ti WINDFORCE OC 12G?

Bykski lists the WINDFORCE OC 12G, model GV-N407TWF3OC-12GD. Confirm the PCB revision against the supported layout before ordering.

Which RTX 4070 SUPER does Bykski list for this block?

The Gigabyte AORUS GeForce RTX 4070 SUPER MASTER 12G, model GV-N407SAORUS M-12GD, is listed. Check that the PCB matches before ordering.

What RGB header does the block use?

Use a 5V 3-pin addressable RGB header. A 12V 4-pin RGB header can damage the lighting.

What fittings do I need?

Use G1/4 fittings that match your tubing. Use the supplied stop plugs to close the unused ports.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.