Bykski · N-GV5090DWF-SR
Full-cover GPU water block for Gigabyte RTX 5090 and 5090 D
The Bykski N-GV5090DWF-SR replaces the stock cooler on supported Gigabyte cards such as the GeForce RTX 5090 GAMING OC 32G. Its copper cold plate transfers heat from the GPU core, memory, and voltage regulators to a custom liquid cooling loop. The included aluminum backplate mounts behind the card.
Fits
Select Gigabyte RTX 5090 and 5090 D cards
Backplate
Black aluminum backplate
Compatibility
Bykski lists these Gigabyte GeForce cards for the PCB layout shown here.
- ✓Gigabyte GeForce RTX 5090 GAMING OC 32G (GV-N5090GAMING OC-32GD)
- ✓Gigabyte GeForce RTX 5090 D GAMING OC 32G (GV-N509DGAMING OC-32GD)
- ✓Gigabyte GeForce RTX 5090 D WINDFORCE 32G (GV-N509DWF3-32GD)
Before ordering, confirm the exact model number and compare your card’s PCB, mounting holes, and component layout with Bykski’s photo.
Bykski’s bare-board photo for checking component placement and mounting holes.
Design Highlights
Cooling for the core, memory, and power delivery
The cold plate draws heat from the GPU core, memory, and voltage regulators into the same coolant loop. Its contact surfaces follow the layout of the supported boards.
Jet-fed microchannels
Bykski specifies up to 56 jet-fed microchannels in the cold plate. The 0.3 mm channels increase the cold plate’s surface area in contact with coolant.
Stainless steel panel
The 304 stainless steel outer panel gives the block its slim profile. The aluminum backplate mounts on the other side of the PCB, outside the coolant path.
Key Specifications
| Model (SKU) | N-GV5090DWF-SR |
|---|
| Cold plate | Copper cold plate |
|---|
| Block body | 304 stainless steel panel and POM components |
|---|
| Backplate | Black aluminum backplate, passive |
|---|
| Port thread | G1/4 female |
|---|
| Water block (L × W × T) | 261.99 × 137.51 × 17.00 mm |
|---|
| Backplate (L × W × T) | 243.40 × 137.51 × 4.68 mm |
|---|
| Copper plate length | 217.3 mm |
|---|
| Net weight | 1.9 kg |
|---|
| Maximum working pressure | 4 bar |
|---|
| Working temperature | −20 to 60 °C |
|---|
| Seal material | EPDM |
|---|
Bykski drawing. Water block above, backplate below. Dimensions are in millimeters.
Which Version Do I Need?
Check the exact card model and PCB layout first. Each block has its own fit list.
Bykski N-GV5090DWF-SRTHIS PAGE
Choose this model for a slim stainless steel panel and a matching Gigabyte PCB.
Choose the X if you want an acrylic window and 5V addressable RGB. Check its PCB list for your card.
Consider the V3 for an RTX 5090 D GAMING OC 32G build that needs a transparent coolant path and a centered fitting terminal.
Choose this separate block for the NVIDIA GeForce RTX 5090 Founders Edition.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplateThermal pad setMounting hardware set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the PC, remove the graphics card, and take off its original cooler and backplate. Clean the old thermal material from the GPU, memory, and power components.
2Cut the supplied thermal pads to fit the marked memory and power-delivery components, and remove the film from both sides. Apply a thin, even layer of your own thermal paste to the GPU die.
3Align the block and backplate with the PCB mounting holes. Secure them with the supplied hardware and tighten gradually for even pressure.
4Connect the block to the loop using G1/4 fittings and tubing. Fill the loop and leak-test it with only the pump powered before turning on the graphics card.
For the custom loop, you also need a pump, reservoir, radiator, G1/4 fittings, matching tubing, and coolant.
Bykski’s installation diagram. The shaded areas around the die show the thermal pad positions. Apply paste to the center die.
FAQ
How can I tell whether this RTX 5090 water block fits my Gigabyte card?
Match the model number in the compatibility list to the label on your card, then compare the PCB with Bykski’s photo.
Which Bykski water block fits the RTX 5090 Founders Edition?
The N-RTX5090FE-SR is the separate water block for NVIDIA’s GeForce RTX 5090 Founders Edition.
What fittings fit this block?
Use fittings with male G1/4 threads and choose the tubing size to match your fittings.
What else do I need for a working loop?
Use a pump, reservoir, radiator, fittings, tubing, and coolant. Leak-test the filled loop before powering the graphics card.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.