Bykski · N-RTX5000-X-V2
Full-cover water block for the Leadtek Quadro RTX 5000 16GB
The Bykski N-RTX5000-X-V2 is a full-cover water block for the Leadtek Quadro RTX 5000 16GB PCIe workstation card. It replaces the factory air cooler. Its nickel-plated copper cold plate transfers heat from the GPU, memory, and voltage regulators to the coolant in a custom loop. The block connects to the loop through G1/4 ports.
Fits
Leadtek Quadro RTX 5000 16GB PCIe
Coverage
GPU core, memory, and VRM
Cold plate
Nickel-plated T2 copper
Compatibility
Supported PCB
- ✓Leadtek NVIDIA Quadro RTX 5000 16GB GDDR6, full-height PCIe workstation card with the matching PCB layout.
The photo shows the rear of the PCB. Before ordering, use the Bykski installation drawing of the component side to match your board’s outline, component layout, and mounting holes.
Leadtek NVIDIA Quadro RTX 5000 PCB, rear view.
Design Highlights
Direct cooling for the core, memory, and VRM
The T2 copper cold plate spans the GPU, memory, and power components. Coolant passes through jet microchannels in the cold plate to carry heat into the loop.
G1/4 ports along the long edge
The black POM terminal sits along the long edge of the block. Its G1/4 threads accept fittings sized for your loop tubing. A stainless steel panel covers the outer face of the block.
Key Specifications
| Model | N-RTX5000-X-V2 |
|---|
| Block type | Full-cover GPU water block for custom loops |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Cold plate | Nickel-plated T2 copper |
|---|
| Cold plate length | 186.13 mm |
|---|
| Outer panel | Stainless steel |
|---|
| Finish color | Black and gunmetal |
|---|
| Port terminal | Black POM |
|---|
| Port thread | G1/4 |
|---|
| Block dimensions | 261.69 × 107.99 × 22.30 mm (L × H × T) |
|---|
| Backplate | None included |
|---|
| Lighting | None |
|---|
Water block dimensions in millimeters (Bykski drawing)
Which Version Do I Need?
Check that your card is a Leadtek Quadro RTX 5000 16GB, then match its PCB to the drawing. RTX A5000, RTX 5000 Ada Generation, and RTX PRO 5000 Blackwell are separate card models.
What's in the Box
1 × full-cover GPU water block5 × 1.5 mm thermal pad strips4 × 0.5 mm mounting gaskets4 × M2 × 5 mm spring screws9 × M2 × 5 mm flat-head screws
The PCB in the assembly diagram is your graphics card.
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
1 Water block · 2 Thermal pads · 3 Your graphics card PCB · 4 Mounting gaskets · 5 Spring screws · 6 Flat-head screws
Installation & Use
1Power off the system and remove the graphics card. Take off the factory cooler and clean away the old paste and pad residue.
2Check that the block's mounting holes line up with the bare PCB before applying pads or paste.
3Cut the 1.5 mm pads to fit the marked memory and MOSFET areas. Peel off any protective film from both sides before placing the pads. Leave the inductors bare and apply thermal paste to the GPU die.
4Align the block and PCB. Place the four gaskets at the mounting holes around the GPU die as shown. Tighten the spring screws gradually in a cross pattern and secure the remaining holes with the flat-head screws.
5Connect the block to your loop using G1/4 fittings. Fill and bleed the loop, then leak-test with only the pump powered before turning on the graphics card.
You also need a pump and reservoir (or a pump-reservoir combo), a radiator and fans, tubing, G1/4 fittings sized for the tubing, and coolant.
Place thermal pads on the marked memory and MOSFET areas around the GPU die. Apply thermal paste to the center die shown under the applicator.
FAQ
Do I need a separate pump and radiator?
Yes. This block uses an external pump and radiator in a custom liquid cooling loop.
How do I check if the block will fit my case?
Use the block dimensions to check clearance around the card, including space for fittings and tubing. Check the case's mounting space for the radiator and fans you plan to use.
What thermal pads should I use?
Use the supplied 1.5 mm pads on the memory and MOSFET areas shown in the installation drawing. Apply thermal paste to the GPU die.
Does a backplate come with the block?
No. This configuration ships without a backplate.
Notes- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.