120 mm Fan Copper Radiator, 28 mm | FormulaMod Fm-CoRa2

FormulaMod · Fm-CoRa2

28 mm copper and brass radiator for custom PC loops

The FormulaMod Fm-CoRa2 is a copper and brass radiator for custom PC water cooling. Its 28 mm body takes 120 mm fans, which move air through the fins to remove heat from the coolant. It comes in four lengths so you can match the radiator to the mounting space in your case.

Fits
120 mm fans
Body thickness
28 mm
Nominal sizes
120 / 240 / 360 / 480 mm
Loop ports
2 × G1/4

Compatibility

Choose the radiator size for your case mount. All four sizes use 120 mm fans.

  • ✓120 mm radiator: 1 fan position per side
  • ✓240 mm radiator: 2 fan positions per side
  • ✓360 mm radiator: 3 fan positions per side
  • ✓480 mm radiator: 4 fan positions per side

Check your case manual for the supported radiator mount, then compare the full radiator dimensions below. Allow room for the fans, fittings, and tubing.

Design Highlights

28 mm radiator body

Use the 28 mm body thickness when planning your build, then add the thickness of the fans and check the space at the port end for fittings and tubing.

Two G1/4 ports at one end

Both connections are on the same end of the radiator. Fit G1/4 fittings that match the tubing in your loop.

Key Specifications

MaterialsCopper and brass
ColorBlack
Coolant ports2 × G1/4
Mounting threadM3
Coolant channels14
Pressure test value1.5 bar
Fm-CoRa2-120154 × 122 × 28 mm
Fm-CoRa2-240276 × 122 × 28 mm
Fm-CoRa2-360396 × 122 × 28 mm
Fm-CoRa2-480516 × 122 × 28 mm

480 mm at top, 360 mm below it, 240 mm at lower left, and 120 mm at lower right. Table dimensions are body length × width × thickness.

Which Version Do I Need?

Both models use 120 mm fans and have the same body length and width in each matching size. Compare body thickness when checking your case clearance.

FormulaMod Fm-CoRa2THIS PAGE
Choose this 28 mm version when you need more clearance for the fans or nearby hardware.
Choose this 39 mm version if your build calls for a thicker radiator and the case has room for it and the fans.

What's in the Box

1 × radiator in your selected sizeFan mounting screws

Installation & Use

1
Check the radiator mount and test-fit the radiator and fans. Leave room at the port end to route the tubing.
2
Mount the fans and radiator with M3 screws of the correct length. FormulaMod specifies M3 × 30 mm for 25 mm thick fans. For thinner fans or nonstandard screw holes, check how far the screw will enter the radiator.
3
Keep screw penetration into the radiator to 5 mm or less on the fin side.
4
Install G1/4 fittings in both ports and connect the tubing. Fill and leak-test the loop before powering the PC hardware.

A complete custom loop uses 120 mm radiator fans, tubing with matching G1/4 fittings at the radiator, a pump, a reservoir, a water block, and coolant.

FormulaMod mounting diagram. Left shows screws that are too long. Right shows screws of the correct length.

FAQ

Are the 360 mm and 480 mm models actually 360 and 480 mm long?

The 360 mm model is 396 mm long, and the 480 mm model is 516 mm long. The size labels identify the fan layout.

What fittings does the Fm-CoRa2 use?

Both ports take G1/4 fittings. Match the tubing side of each fitting to your tubing type and size.

How deep can the mounting screws go?

FormulaMod limits penetration into the radiator to 5 mm on the fin side. Check the screw length against your fan and mount before tightening.

What is the difference between Fm-CoRa2 and Fm-CoRa2H?

Fm-CoRa2 has a 28 mm body and Fm-CoRa2H has a 39 mm body. Both use 120 mm fans and come in the same four nominal sizes.

Product Gallery

Notes
  • Overlong screws can damage the radiator and cause leaks.