CMP 170HX AIO GPU Cooler, 360/480 mm | Astralcooler

Astralcooler · CMP 170HX GPU AIO

All-in-one GPU liquid cooling for one or two cards

This Astralcooler all-in-one liquid cooler replaces the stock cooler on supported NVIDIA CMP 170HX and A30 24GB PCIe boards. Each full-cover water block transfers heat from the GPU core, memory, and power circuitry to the radiator. Choose the 360 mm kit for one card or the 480 mm kit for two.

Fits
NVIDIA CMP 170HX
360 mm kit
1 GPU water block
480 mm kit
2 GPU water blocks
Cold plate
T2 copper

Compatibility

Supported NVIDIA GPU models

  • ✓NVIDIA CMP 170HX
  • ✓NVIDIA A30 24GB PCIe

Astralcooler also lists the NVIDIA A100 40GB without specifying the board version. Confirm your exact card model and PCB layout with us before ordering.

Manufacturer’s PCB diagram for the NVIDIA CMP 170HX.

Design Highlights

One radiator for the dual-block kit

The 480 mm kit connects two full-cover GPU water blocks to one radiator. The 360 mm kit uses one block for a single card.

Full-cover T2 copper cold plate

The cold plate covers the GPU core, memory, and power components such as MOSFETs. Jet microchannels increase the surface area in contact with the coolant.

Pump built into the tubing

An inline pump circulates coolant through the EPDM tubing between the water block and the radiator.

Key Specifications

360 mm radiator399 mm long × 60 mm thick with fans
480 mm radiator517 mm long × 66 mm thick with fans
GPU water block265 × 120 × 17.5 mm (L × H × T)
Cold plateT2 copper with a nickel-plated coolant contact surface
Cold plate conductivityUp to 401 W/(m·K), material specification
Radiator coolant contact surfaceHard-anodized aluminum
TubingEPDM
Inline pumpCeramic shaft and bushing, three-phase six-pole motor
Radiator fans3,000 RPM ±10%, 99.5 CFM, 5.3 mm H₂O, 41 dB(A)

Manufacturer’s side view of the 480 mm kit. The 70, 360, and 480 mm arrows show the spacing between components in this layout.

Which Version Do I Need?

Choose by GPU count and the radiator space available in your chassis.

Astralcooler AIO · 360 mmTHIS PAGE
Choose this configuration for one compatible GPU and a 360 mm radiator mount.
Astralcooler AIO · 480 mmTHIS PAGE
Choose this configuration for two compatible GPUs and a 480 mm radiator mount.
Choose the standalone block if you already have a custom loop and need only the GPU water block.

What's in the Box

360 mm kit: 1 radiator, 1 water block, 1 inline pump, 3 radiator fans480 mm kit: 1 radiator, 2 water blocks, 2 inline pumps, 4 radiator fansEPDM tubing

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Manufacturer’s illustration of the 360 mm kit.

Installation & Use

1
Power down the system, remove the card, and take off the original cooler. Clean residue from the GPU die and the other contact areas.
2
Place thermal pads at the points shown for your PCB. Apply your own thermal paste to the GPU die.
3
Align the GPU water block and backplate with the mounting holes. Follow the mounting diagram and tighten the screws gradually and evenly.
4
Mount the radiator and route the tubing without kinks. Confirm the pump and fan connections for your kit, then check for leaks before powering the card.

Allow room for the radiator, fans, and tubing. Have your own thermal paste ready before installation.

CMP 170HX mounting diagram. 1 Water block · 2 Thermal pads · 3 GPU PCB · 4 Spring screws · 5 Backplate · 6 Backplate screws.
The CMP 170HX guide specifies five 1.5 mm pads, M2 × 7 mm spring screws, and M2 × 8 mm backplate screws for the illustrated block.

FAQ

What is the difference between the 360 mm and 480 mm kits?

The 360 mm kit has one GPU water block. The 480 mm kit has two water blocks connected to one radiator.

How do I check fit on an NVIDIA A100 40GB?

NVIDIA lists both PCIe and SXM4 versions of the A100 40GB. Ask us to verify the PCB for your exact card before ordering.

How involved is installation on a CMP 170HX?

You’ll remove the stock cooler, apply thermal pads and your own thermal paste, and attach the block and backplate. You’ll also need to mount the radiator and route the tubing.

How much space do I need for the radiator and fans?

Allow for 399 mm of length and 60 mm of thickness for the 360 mm kit, or 517 mm and 66 mm for the 480 mm kit. Leave room for the tubing at the end of the radiator.