Barrow · SPB17-S-V2
Standalone DDC-style pump with PWM and manual speed control
The Barrow SPB17-S-V2 is a standalone DDC-style pump for custom PC water cooling loops. It circulates coolant between the reservoir, water blocks, and radiator. The pump comes with an acrylic top and aluminum alloy housing. Set the speed with a motherboard PWM signal or switch to the manual knob.
Design Highlights
Barrow’s pump cavity illustration.
Top inlet, side outlet
Coolant enters through the top of the acrylic pump cover and leaves through the side port. Both ports take G1/4 fittings.
Switch from PWM to manual speed
The pump ships in PWM mode. Turn the knob clockwise for manual control. Turn it fully counterclockwise to return to PWM.
LRC 2.0 lighting
The LEDs light the acrylic top. Motherboard lighting control requires an ARGB adapter cable and a compatible 5 V 3-pin ARGB header.
Key Specifications
| Model | SPB17-S-V2 |
|---|
| Pump top | Acrylic |
|---|
| Housing | Aluminum alloy |
|---|
| Housing colors | Black or silver |
|---|
| Dimensions (L × W × H) | 62.20 × 62.20 × 48.50 mm |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Rated voltage | 12 V DC |
|---|
| Rated current | 1.4 A |
|---|
| Rated power | 17 W |
|---|
| Pump power connector | 4-pin Molex |
|---|
| Speed control | 4-pin PWM signal or manual knob |
|---|
| Maximum flow | 960 L/h |
|---|
| Maximum speed | 4,000 RPM |
|---|
| Lighting | Barrow LRC 2.0 · 5 V 3-pin ARGB |
|---|
| Temperature limit | Below 60 °C |
|---|
| Noise (Barrow spec) | Below 40 dB |
|---|
| Service life (Barrow spec) | Over 50,000 hours |
|---|
Barrow’s dimension drawing, in millimeters. Arrows point to the two G1/4 ports.
Which Version Do I Need?
Barrow SPB17-S-V2THIS PAGE
Choose this standalone pump when you are running a separate reservoir in your loop.
Choose a pump-and-reservoir option here if you want the reservoir to mount directly to the pump.
Choose this through-hole version when your distro plate specifies the SPB17-T V2.
Choose the standalone version with exposed cooling fins on the base if you have room for its 53 mm height.
What's in the Box
1 × complete SPB17-S-V2 pump
The lighting controller is sold separately.
Installation & Use
1Mount the pump with the inlet facing up and the reservoir above it so coolant can flow into the pump by gravity.
2Connect the reservoir to the top inlet and the rest of the loop to the side outlet with G1/4 fittings and matching tubing.
3Connect the 4-pin Molex lead to the power supply. For PWM speed control, connect the separate 4-pin PWM lead to a motherboard PWM header.
4For motherboard lighting control, use an ARGB adapter cable to connect the Barrow lighting lead to a compatible 5 V 3-pin ARGB header. Keep the lighting lead off 12 V RGB headers.
5Fill the reservoir and let coolant reach the pump before applying power. Power only the pump to check for leaks before powering the rest of the PC. Never run the pump dry.
To complete the loop, you’ll need a separate reservoir, G1/4 fittings, matching tubing, a water block, a radiator, and coolant.
From left to right, the power plug, PWM signal plug, lighting plug, and speed knob.
FAQ
How do I switch between PWM and manual speed control?
Turn the speed knob clockwise for manual control. Turn it fully counterclockwise to return to PWM.
Which port is the inlet?
The top port is the inlet and the side port is the outlet. Both use G1/4 fittings.
Can I control the lighting from my motherboard?
Yes. You’ll need an ARGB adapter cable and a compatible 5 V 3-pin ARGB header. The lighting controller is sold separately.
Do I need a separate pump top or reservoir?
The acrylic pump top is already fitted. Use a separate reservoir to feed coolant into the pump.
How do I power the pump?
Use the 4-pin Molex lead from the power supply. The separate 4-pin PWM lead carries the speed-control signal.
Notes- In case of product appearance structure upgrade,without further notice,in kind prevail
- In case product appearance upgrade, without further notice, prevail in kind.