Barrow Distro Plate PWM Water Pump, 17 W, SPB17-T V2

Barrow · SPB17-T V2

17 W PWM water pump for Barrow distro plates

The Barrow SPB17-T V2 is a 17 W water pump that circulates coolant in a custom PC liquid cooling loop. It bolts directly to a compatible Barrow distro plate with a dedicated pump mount. Run it in PWM mode or set the speed with its manual knob.

Fits
Select Barrow distro plates
Pump power
17 W · 12 V DC
Max. flow
960 L/h
Speed control
PWM or manual

Compatibility

Barrow lists this pump for these distro plate models.

  • ✓LLO11-SDB (original) · Lian Li O11
  • ✓LLO11-SDB M · Lian Li O11 Mini
  • ✓ANTECTE-SDB (original) · Antec Torque
  • ✓TTP90-SDB · Thermaltake Core P90 TG

Match the exact plate model and revision before ordering. Check for the dedicated through-hole pump mount and seal groove.

Design Highlights

Through-hole mount

Four mounting screws pass through the acrylic top to secure the pump to the distro plate. A rubber seal sits in the plate’s groove at the joint.

PWM or manual speed control

PWM is the factory default. Turn the knob clockwise to switch to manual control, then turn it fully counterclockwise to return to PWM.

Key Specifications

ModelSPB17-T V2
Pump typePermanent-magnet centrifugal
MaterialsAcrylic top, aluminum alloy housing
Size (L × W × H)62.2 × 62.2 × 48.5 mm
Pump top threadG1/4
Rated voltage12 V DC
Rated current1.4 A
Rated power17 W
Speed signal4-pin PWM
Max. speed4,000 RPM
Max. flow960 L/h
Max. head5–6 m
Working temperatureBelow 60 °C
Rated noiseBelow 40 dB
Rated service lifeOver 50,000 hours
LightingBarrow LRC 2.0, 5 V addressable lighting (motherboard adapter cable included)
Cover colorsBlack, blue, red, silver

Barrow drawing in millimeters. Arrows point to the G1/4 openings.

Which Version Do I Need?

Barrow SPB17-T V2THIS PAGE
Choose this model when your Barrow distro plate specifies SPB17-T V2.
Choose this finned-housing version if your distro plate specifies SPB17-T PLUS.
Choose this model if you’re pairing the pump with a compatible tube reservoir.

What's in the Box

1 × Barrow SPB17-T V2 pump kit in the selected cover colorAdapter cable for a 5 V 3-pin ARGB motherboard header

The lighting controller is sold separately.

Installation & Use

1
Seat the black rubber seal in the groove on the matching distro plate. Align the pump and secure it with four mounting screws.
2
Identify the inlet and outlet before connecting the loop. Keep the inlet facing up so coolant can feed into the pump by gravity.
3
Check the pump’s power plug and connect it to a matching 12 V DC power supply connector. Connect the separate PWM signal lead to a 4-pin PWM header.
4
For LRC 2.0 lighting, use a compatible controller. For motherboard sync, connect the pump’s lighting lead to a 5 V 3-pin ARGB header using the included adapter cable.
5
Fill the loop so coolant reaches the pump before powering it. Never run the pump dry. Leak-test the loop before powering the rest of the PC.

You also need a compatible distro plate, radiator, tubing, fittings, and coolant.

FAQ

Will it fit any Barrow distro plate?

Check the exact model and revision against the fit list. The pump requires the matching through-hole mount and seal groove.

How do I control the pump speed?

Use the 4-pin PWM signal lead for automatic speed control, or turn the knob clockwise to switch to manual speed control.

Does it use a 5 V or 12 V lighting header?

Barrow specifies 5 V for LRC 2.0 lighting. Use the included adapter cable to connect to a 5 V 3-pin ARGB motherboard header. The pump motor has its own 12 V DC power connection.

What is the pump’s maximum flow rate?

Barrow rates it at a maximum of 960 L/h and lists a maximum head of 5–6 m.

Can I power the pump before filling the loop?

Fill the loop first and make sure coolant has reached the pump. Running it dry can damage it.

Notes
  • In case product appearance upgrade, without further notice, prevail in kind.