Barrow · BS-GIG5090-PA
Full-cover water block for Gigabyte RTX 5090 D
The Barrow BS-GIG5090-PA is a full-cover GPU water block for select Gigabyte GeForce RTX 5090 D cards, including the GAMING OC 32G. It replaces the factory cooler so your custom loop can cool the GPU core, memory, and power delivery components. The block comes with an aluminum backplate.
Fits
Select Gigabyte RTX 5090 D 32G
Ports
G1/4 inlet and outlet
Compatibility
Barrow lists these Gigabyte PCB layouts for the BS-GIG5090-PA.
- ✓Gigabyte GeForce RTX 5090 D GAMING OC 32GGV-N509DGAMING OC-32GD
- ✓Gigabyte GeForce RTX 5090 D GAMING 32GGV-N509DGAMING-32GD
- ✓Gigabyte GeForce RTX 5090 D WINDFORCE OC 32GGV-N509DWF3OC-32GD
- ✓Gigabyte GeForce RTX 5090 D WINDFORCE 32GGV-N509DWF3-32GD
- ✓Gigabyte AORUS GeForce RTX 5090 D MASTER 32GGV-N509DAORUS M-32GD
- ✓Gigabyte AORUS GeForce RTX 5090 D MASTER ICE 32GGV-N509DAORUSM ICE-32GD
- ✓Gigabyte AORUS GeForce RTX 5090 D XTREME WATERFORCE 32GGV-N509DAORUSX W-32GD
Before ordering, match the full model name and part number on your card, then verify its PCB layout against Barrow’s compatibility information.
Gigabyte GeForce RTX 5090 D GAMING OC 32G as shown in Barrow’s compatibility guide.
Design Highlights
Barrow’s view of the cold plate with the thermal pads in place.
GPU, memory, and power delivery cooling
The copper cold plate collects heat from the GPU core, memory, and power delivery components. Coolant carries that heat into the loop.
Jet microchannels over the GPU
Barrow specifies 43 microchannels. The grooves are 0.5 mm wide with 0.3 mm spacing between them.
Clear acrylic with 5V lighting
The clear acrylic top shows the coolant path and the built-in Barrow LRC 2.0 lighting. For motherboard control, connect the lighting through a compatible adapter cable to a 5V 3-pin ARGB header.
Key Specifications
| Model | BS-GIG5090-PA |
|---|
| Cold plate | Copper |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Passive aluminum alloy |
|---|
| Coverage | GPU core, memory, and power delivery components |
|---|
| Block dimensions (L × W × T) | 230.50 × 153.40 × 24.20 mm |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Lighting | Barrow LRC 2.0, 5V ARGB |
|---|
| Color options | Black (BS-GIG5090-PA-BK) White (BS-GIG5090-PA-WT) |
|---|
Barrow’s drawing shows the overall block dimensions in millimeters.
Which Version Do I Need?
Choose the Barrow part number that matches the PCB on your graphics card.
Barrow BS-GIG5090-PATHIS PAGE
Choose this block for the Gigabyte RTX 5090 D models listed above.
Check this block for an ASUS ROG Astral card such as the RTX 5090 D O32G Gaming.
Check this block for a listed MSI card such as the RTX 5090 D 32G Suprim SOC.
Check this block for a listed GALAX or Gainward card such as the GALAX RTX 5090 D Boomstar Luna OC.
What's in the Box
1 × full-cover GPU water block1 × aluminum alloy backplate2 × G1/4 stop plugs1 × mounting hardware setThermal pad set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Barrow’s photo of the Black backplate.
Installation & Use
1Before removing the card, check Gigabyte’s service guidance for your exact model. See Gigabyte FAQ 4371, Liquid Metal & Composite Metal Grease User Guide, for the AORUS RTX 5090 D XTREME WATERFORCE (liquid metal) and the AORUS RTX 5090 D MASTER and MASTER ICE (conductive composite metal grease). If the factory cooler on any of these three cards has already been removed, Gigabyte recommends sending the card to its service center for proper restoration before putting it back into operation.
2For the GAMING and WINDFORCE models listed above, shut down and disconnect power before removing the card and its factory cooler. Clean off the old thermal material and check the PCB layout and mounting holes against Barrow’s guide.
3Once the card is ready for block installation, cut the thermal pads to fit the marked contact areas in Barrow’s diagram. Apply your own thermal paste to the GPU core.
4Align the block, PCB, and backplate. Install the spacers, washers, and screws at the locations shown in Barrow’s mounting diagram.
5Confirm the block’s inlet and outlet positions before connecting the loop with G1/4 fittings. Seal unused ports with the supplied stop plugs.
6Fill and leak-test the loop with the graphics card unpowered.
You also need a pump, reservoir, radiator with fans, tubing, matching G1/4 tube fittings, and coolant.
Barrow’s pad map (Figure 2). 1 = 1.2 mm, 2 = 0.5 mm, and 3 = 1.0 mm.
FAQ
Does this block fit my Gigabyte RTX 5090?
Barrow lists the RTX 5090 D cards shown above. Look up the exact part number on your card and confirm the PCB layout before you order.
Is the included backplate water-cooled?
The included aluminum alloy backplate is passive. Coolant runs through the water block on the front of the card.
Which fittings do I need?
Use G1/4 fittings sized for your tubing. The box includes stop plugs. Supply your own tube fittings, including any compression fittings shown in product photos.
How do I connect the lighting to my motherboard?
Use a separately purchased Barrow-compatible adapter cable and a 5V 3-pin ARGB header. Keep the lighting cable off 12V 4-pin RGB headers.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.