Barrow · BS-AST4080-PA
Full-cover water block for ASUS TUF and ROG Strix RTX 4080
The Barrow BS-AST4080-PA replaces the stock cooler on the ASUS TUF Gaming and ROG Strix GeForce RTX 4080 16GB models listed below. Its copper cold plate transfers heat from the GPU core, memory, and power delivery components to the coolant in a custom loop. The block uses G1/4 fittings and comes with an aluminum backplate.
Fits
Select ASUS RTX 4080 16GB PCBs
Compatibility
Barrow lists these ASUS GeForce RTX 4080 16GB models for this block.
- ✓ASUS TUF Gaming RTX 4080 OC (TUF-RTX4080-O16G-GAMING)
- ✓ASUS TUF Gaming RTX 4080 (TUF-RTX4080-16G-GAMING)
- ✓ASUS ROG Strix RTX 4080 OC (ROG-STRIX-RTX4080-O16G-GAMING)
- ✓ASUS ROG Strix RTX 4080 (ROG-STRIX-RTX4080-16G-GAMING)
Before ordering, check the exact model number and PCB layout of your card. See gallery image 2 for the ASUS TUF-RTX4080-16G-GAMING bare PCB.
Official ASUS product image of the TUF Gaming GeForce RTX 4080 with its stock cooler.
Design Highlights
Copper cold plate with jet microchannels
Barrow’s diagrams for the BS-AST4080-PA describe a 10 mm copper blank and as many as 43 jet microchannels. The jet microchannels increase the surface area where coolant passes over the GPU core.
Clear acrylic with addressable lighting
The clear top shows the coolant path and the LRC 2.0 lighting. Choose the sync cable for a motherboard with a 5V 3-pin ARGB header, or choose the manual controller to adjust the lighting separately.
Black or white aluminum backplate
The included passive backplate mounts behind the graphics card PCB. Both colors are available with either lighting control option.
Key Specifications
| Model | BS-AST4080-PA |
|---|
| Cooling coverage | GPU core, memory, and power delivery components |
|---|
| Cold plate | Copper |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Passive aluminum alloy, black or white |
|---|
| Inlet and outlet thread | G1/4 |
|---|
| Width including terminal | 156.90 mm |
|---|
| Maximum block thickness shown | 23.80 mm |
|---|
| Lighting | LRC 2.0 ARGB, 5V 3-pin via sync cable |
|---|
Barrow dimension drawing. Measurements are in millimeters.
Which Version Do I Need?
Use the model number on your card to choose the right block.
Barrow BS-AST4080-PATHIS PAGE
Choose this block for one of the ASUS TUF Gaming or ROG Strix RTX 4080 PCB layouts listed above.
Choose this listing if you have the NVIDIA GeForce RTX 4080 Founders Edition.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set
Select a sync cable or a manual lighting controller when ordering.
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the system and remove the graphics card. Unplug the stock cooler before lifting it away.
2Clean the old thermal material from the GPU die and its contact areas. Apply your own thermal paste to the die and cut and place the pads using Barrow’s pad layout for this model.
3Align the water block, PCB, and backplate. Follow Barrow’s screw and washer diagram when fastening the assembly.
4Confirm the inlet and outlet positions before connecting the tubing with G1/4 fittings. Close unused ports with the supplied stop plugs.
5Connect the lighting through the selected cable or controller. If using motherboard sync, connect the cable to a 5V 3-pin ARGB header.
6Leak-test the loop before powering the graphics card.
You’ll also need G1/4 tube fittings, tubing, a pump, a reservoir, a radiator with fans, coolant, and your own thermal paste.
In Barrow’s drawing, (1) is the water block, (2) black ABS washers, (3) the graphics card PCB, (4) the backplate, (5) spring screws, (6) round-head screws, and (7) flat-head screws. The screws in (6) and (7) have cross-shaped recesses.
FAQ
Which ASUS TUF and ROG Strix RTX 4080 cards does this water block fit?
Barrow lists the OC and non-OC 16GB Gaming models in both families. Match your exact card model and PCB layout to the Compatibility section above.
Can I use a 12V RGB header?
Use a 5V 3-pin ARGB header with the sync cable. Connecting the lighting to a 12V 4-pin RGB header can damage it.
Can I get a white backplate?
Yes. The aluminum backplate comes in black or white. Either color can be paired with the sync cable or the manual controller.
What fittings are included?
The box includes two G1/4 stop plugs. Supply your own G1/4 tube fittings to connect the block to your loop.
Notes- 2. This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- 3. The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- 4. Not responsible for any damage caused by or when using this product. Please use it at your own risk.