RX 9070 XT Water Block for PowerColor Hellhound 16GB with Backplate — Barrow BS-DAK9070XT-PA

Barrow · BS-DAK9070XT-PA

Full-cover water block for PowerColor Hellhound RX 9070 XT

The Barrow BS-DAK9070XT-PA is a full-cover water block for the PowerColor Hellhound Radeon RX 9070 XT 16GB cards listed below. It replaces the stock cooler and transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. The included aluminum backplate mounts behind the PCB.

Fits
PowerColor Hellhound RX 9070 XT 16GB
Cold plate
Copper
Ports
G1/4
Lighting
5V ARGB

Compatibility

Barrow lists these two PowerColor Hellhound models.

  • ✓Hellhound Radeon RX 9070 XT 16GB (black) · RX9070XT 16G-L/OC
  • ✓Hellhound Spectral White Radeon RX 9070 XT 16GB · RX9070XT 16G-L/OC/WHITE

Before ordering, verify your exact graphics card model and PCB layout. Contact FormulaMod if you need help confirming the fit.

PowerColor Hellhound Spectral White (left) and Hellhound black (right).

Design Highlights

Microchannels over the GPU

The machined copper cold plate spans the GPU, memory, and voltage regulators. Coolant flows through microchannels above the GPU contact area.

Clear acrylic top and G1/4 ports

The clear top leaves the coolant path visible. Use G1/4 fittings sized for your tubing to connect the block to the loop.

5V addressable lighting

Both backplate options have 5V ARGB lighting. To sync the lighting with your motherboard, use a compatible adapter cable and a 5V three-pin ARGB header.

Key Specifications

ModelBS-DAK9070XT-PA
Cooling coverageGPU core, memory, and voltage regulators
Cold plateCNC-machined copper
TopClear acrylic
BackplateAluminum alloy, black or white
Water block size (L × W × max. thickness)194.60 × 123.20 × 24 mm
Port threadG1/4
Lighting5V ARGB
Motherboard lighting header5V three-pin ARGB via an adapter cable

Barrow dimension drawing. Measurements are in millimeters.

Which Version Do I Need?

Start with your graphics card maker and exact model, then check the PCB layout for that block.

Barrow BS-DAK9070XT-PATHIS PAGE
Barrow lists this block for the PowerColor Hellhound cards above. Contact FormulaMod to confirm the backplate model before ordering the white option.
Choose the XFX version for the listed XFX RX 9070 XT 16GB Overseas Ultra cards.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate in the selected color2 × G1/4 stop plugsMounting hardware setThermal pad set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

White and black backplate options. Each block comes with one backplate.

Installation & Use

1
Power off the PC, remove the graphics card, and take off the factory cooler and backplate. Clean off the old thermal materials.
2
Cut and place the thermal pads according to Barrow’s diagram. Apply your own thermal paste to the GPU die.
3
Align the water block and backplate on either side of the PCB. Follow Barrow’s mounting diagram for the positions of the screws and washers.
4
Check the inlet and outlet positions, then connect the loop with G1/4 fittings. Close unused ports with the stop plugs.
5
Leak-test the loop before powering on the graphics card.

You also need a pump, radiator, coolant, tubing, and G1/4 fittings that match your tubing.

Barrow’s BS-DAK9070XT-PA installation diagram shows where to use ① 1.2 mm, ② 0.5 mm, and ③ 1.0 mm pads.

FAQ

Will this RX 9070 XT water block fit my card?

Barrow lists two PowerColor Hellhound models in the compatibility section above. Check your exact model number and PCB layout before ordering.

Does it come with a backplate?

Yes. One aluminum backplate comes with the block. Select black or white when ordering.

What fittings do I need?

Use G1/4 fittings matched to your tubing. The two included stop plugs close unused ports, and the tubing fittings are separate.

What motherboard header does the lighting use?

Use a 5V three-pin ARGB header with a compatible adapter cable.

Notes
  • 4. We are not responsible for any damage caused during the use of this product. Please use it at your own risk.
  • The copper plate of the water block is machined by a CNC machine tool.