Barrow · BS-GIG4090-PA
Full-cover water block for Gigabyte RTX 4090
The Barrow BS-GIG4090-PA replaces the stock cooler on supported Gigabyte GeForce RTX 4090 cards, including the Gaming OC 24G. Its copper cold plate transfers heat from the GPU core, memory, and power delivery components into a custom liquid cooling loop. An aluminum backplate mounts behind the card.
Fits
Gaming OC 24G / AORUS Master 24G
Cold plate
CNC-machined copper
Ports
G1/4 inlet and outlet
Compatibility
Barrow lists these two Gigabyte models.
- ✓Gigabyte GeForce RTX 4090 Gaming OC 24G (GV-N4090GAMING OC-24GD)
- ✓Gigabyte AORUS GeForce RTX 4090 Master 24G (GV-N4090AORUS M-24GD)
Before ordering, verify your exact card model and check that its PCB layout and mounting holes match the block.
Barrow reference photos. Gaming OC 24G on the left, AORUS Master 24G on the right.
Design Highlights
Copper cold plate
Barrow specifies 10 mm copper stock for the cold plate. The clear acrylic top shows the coolant path and port terminal.
Jet microchannels over the GPU core
Coolant flows through 43 jet microchannels in the three-layer core structure. The channels increase the surface area in contact with the coolant.
Addressable lighting
Choose the sync cable option for a motherboard with a 5V 3-pin ARGB header, or select the manual controller option to adjust the lighting by hand.
Key Specifications
| Barrow model | BS-GIG4090-PA |
|---|
| Series | Aurora LRC 2.0 |
|---|
| Cold plate | CNC-machined copper |
|---|
| Top | Clear acrylic |
|---|
| Cooling coverage | GPU core, graphics memory, and power delivery components |
|---|
| Backplate | Passive aluminum alloy, black or white |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Block dimensions (L × W × T) | 226.60 × 151 × 24 mm |
|---|
| Motherboard lighting | 5V 3-pin ARGB via sync cable |
|---|
Barrow dimension drawing. Measurements are in millimeters.
Which Version Do I Need?
Use the full model name on your graphics card label to pick the matching block.
Barrow BS-GIG4090-PATHIS PAGE
For the Gigabyte RTX 4090 Gaming OC 24G and AORUS RTX 4090 Master 24G PCB layouts listed above.
For the original Gigabyte GeForce RTX 4090 WINDFORCE 24G.
For the NVIDIA GeForce RTX 4090 Founders Edition.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate in the selected color2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set
The lighting accessory follows your selection: sync cable or manual controller. Tubing fittings are sold separately.
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Shut down and unplug the PC. Remove the graphics card, disconnect the stock cooler's fan lead, and remove the cooler.
2Clean off the old thermal pads and paste. Cut the supplied pads to match the diagram and place them at the marked contact points on the cold plate. Apply your own thermal paste to the GPU core.
3Align the water block, PCB, and backplate. Secure them with the supplied mounting hardware. Stop and check the alignment if the block does not sit flush.
4Connect the loop to the inlet and outlet with G1/4 fittings. Close the unused openings with the stop plugs.
5For motherboard lighting sync, line up the sync cable with a 5V 3-pin ARGB header. Keep it off 12V 4-pin RGB headers.
6Fill and leak-test the loop with the graphics card unpowered. Power the card only after confirming there are no leaks.
Use G1/4 fittings that match your tubing. For a new loop, you also need tubing, coolant, a pump, a reservoir, a radiator, and fans.
Barrow pad diagram (Figure 2). 1 = 1.2 mm, 2 = 0.5 mm, 3 = 1.0 mm.
FAQ
Which Gigabyte RTX 4090 cards fit this block?
Barrow lists the Gigabyte GeForce RTX 4090 Gaming OC 24G and AORUS GeForce RTX 4090 Master 24G. Match your PCB to the block before ordering.
Does the block include a backplate?
Yes. The kit includes one aluminum backplate in your selected color, black or white.
Which ARGB header do I need for the sync cable?
Use a 5V 3-pin addressable RGB header. Keep the cable off 12V 4-pin RGB headers.
Which tubing fittings do I need?
Use G1/4 fittings sized for your tubing. The two included stop plugs close unused ports, and the tubing fittings are separate.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.
- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.