Barrow · BS-MSG4080M-PA
Full-cover GPU water block for MSI GeForce RTX 4080
The Barrow BS-MSG4080M-PA is a full-cover GPU water block for the MSI GeForce RTX 4080 16GB SUPRIM and GAMING TRIO PCB layouts listed below. It replaces the stock cooler and transfers heat from the GPU core, memory, and VRM into a custom liquid cooling loop. An aluminum backplate mounts behind the PCB.
Fits
MSI RTX 4080 16GB SUPRIM / GAMING TRIO
Cold plate
Copper cold plate
Compatibility
Barrow lists these four MSI graphics cards for this block.
- ✓MSI GeForce RTX 4080 16GB SUPRIM X
- ✓MSI GeForce RTX 4080 16GB SUPRIM
- ✓MSI GeForce RTX 4080 16GB GAMING X TRIO
- ✓MSI GeForce RTX 4080 16GB GAMING TRIO
Barrow’s SUPRIM X PCB photo shows a board marked MS-V511 VER:2.0. Before ordering, verify your exact card model and PCB layout.
Left to right are SUPRIM X, SUPRIM, GAMING X TRIO, and GAMING TRIO.
Design Highlights
Full-cover copper cold plate
Coolant flows through 43 microchannels over the GPU core. The copper cold plate also draws heat from the memory and voltage regulators through thermal pads.
Clear acrylic top with addressable lighting
The clear acrylic top leaves the coolant path visible. Run the Barrow LRC 2.0 lighting from a compatible controller or sync it to a 5V 3-pin motherboard ARGB header with a matching adapter cable.
Aluminum backplate in black or white
The included passive backplate mounts behind the PCB. Select a black or white backplate when choosing the block.
Key Specifications
| Model | BS-MSG4080M-PA |
|---|
| Cold plate | CNC-machined copper |
|---|
| Top | Clear acrylic |
|---|
| Microchannels | 43 channels, 0.5 mm groove width, 0.3 mm spacing |
|---|
| Water block dimensions (L × W × T) | 260.40 × 152.10 × 23.80 mm |
|---|
| Inlet and outlet thread | G1/4 |
|---|
| Backplate | Passive aluminum alloy, black or white |
|---|
| Lighting | Barrow LRC 2.0, 5V 3-pin ARGB |
|---|
Barrow’s block drawing. Dimensions are in millimeters.
Which Version Do I Need?
Match the block to the graphics card’s exact PCB.
Barrow BS-MSG4080M-PATHIS PAGE
Choose this block for one of the listed MSI SUPRIM or GAMING TRIO boards.
Choose this separate block for the NVIDIA GeForce RTX 4080 Founders Edition.
What's in the Box
1 × Full-cover GPU water block1 × Aluminum backplate2 × G1/4 stop plugs1 × Mounting hardware set1 × Thermal pad set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the system and remove the graphics card. Disconnect the fan cable, remove the stock cooler, and clean off the old thermal material.
2Apply your own thermal paste to the GPU die. Place thermal pads at the corresponding contact points for your PCB and block.
3Align the block, PCB, and backplate at the mounting holes. Secure them with the specified washers and screws. If the block does not sit correctly, check contact and alignment before continuing.
4Connect your tubing to the inlet and outlet with G1/4 fittings and seal the unused openings with the stop plugs.
5Connect the lighting to a compatible LRC 2.0 controller or use the adapter cable with a motherboard ARGB header. Use only a 5V 3-pin ARGB header and align the connector with its pinout.
6Leak-test the assembled loop before powering the graphics card.
You also need a pump, reservoir, radiator, coolant, tubing, and G1/4 fittings sized for your tubing.
Barrow’s view of the contact side of the block.
FAQ
Is this a universal RTX 4080 water block?
Barrow lists four specific MSI RTX 4080 16GB boards for this block. Match both the card model and its PCB to the compatibility list before ordering.
Can I connect the lighting to my motherboard?
Use a matching sync adapter cable and a 5V 3-pin ARGB header. You can also use a compatible LRC 2.0 controller.
What fittings do I need for tubing?
Use G1/4 loop fittings that match the tubing you plan to use. The included stop plugs seal unused openings.
Can I choose the backplate color?
Select a black or white aluminum backplate. Each water block comes with one backplate in the finish you select.
Notes- 2. This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- 3. The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- 4. Not responsible for any damage caused by or when using this product. Please use it at your own risk.