7%OFF

Barrow Multi-Angle Hard Tube Bender ABQYG-16A V2 for 12, 14, and 16 mm OD Acrylic and PETG

$19.20 $20.68 now piece
items available
View Details
Barrow · ABQYG-16A V2

Multi-angle bending mold for PC water cooling

The Barrow ABQYG-16A V2 is a bench-top mold for shaping 12, 14, or 16 mm OD acrylic (PMMA) and PETG hard tubing in a custom PC cooling loop. Three adjustable guide arms position the softened tube along your planned route. Set the guides for a corner, an offset, or a U-bend, then hold the tube in place as it sets.

Fits
12, 14, or 16 mm OD
Tube materials
Acrylic (PMMA) / PETG
Guide arms
3 adjustable ABS arms
Color
Black

Use With

Check your hard tubing’s outside diameter (OD) before ordering.

  • ✓12 mm OD acrylic (PMMA) or PETG hard tubing
  • ✓14 mm OD acrylic (PMMA) or PETG hard tubing
  • ✓16 mm OD acrylic (PMMA) or PETG hard tubing

Match the silicone bending insert to the inside diameter of your tubing.

Design Highlights

Set the guides for your tube route

Reposition the guide arms in the straight or curved slots to suit the bend. The scale along the base shows center-to-center spacing.

Barrow’s guide layout for a parallel offset.

Shift the tube sideways with an offset

Barrow shows two guides positioning the tube so its straight ends run parallel on either side of the offset.

Key Specifications

ModelABQYG-16A V2
ColorBlack
Supported tube OD12 mm, 14 mm, or 16 mm
Tube materialsAcrylic (PMMA) or PETG rigid tubing
Guide materialABS plastic
Base plate (L × W × T)435.80 × 119.30 × 16 mm

Barrow’s base plate drawing. Dimensions are in millimeters.

Which Version Do I Need?

Barrow ABQYG-16A V2THIS PAGE
Choose this adjustable mold if you need to change the bend layout or work with more than one supported tube diameter.
Choose an AWGM3 set for fixed-angle bends in one tube size. Select the set by your tube’s outside diameter.

What's in the Box

1 × black bending mold setBase plate3 × guide armsBolts and thumb knobs

Barrow’s view of the mold before assembly.

How to Bend Hard Tubing

1
Plan the tube route and set the guide arms to match the bend you want.
2
Slide a silicone insert that fits the tube’s inside diameter into the section you plan to bend.
3
Rotate the tube over a heat gun so the bend area softens evenly. Keep the hot air away from the mold and avoid touching the heated tube.
4
Move the softened tube to the mold and bend it against the guides in one smooth motion. Hold the bend in place until it sets.
5
Remove the insert, check the tube against your route, then trim and deburr the ends as needed.

Have hard tubing, a heat gun, a silicone bending insert, and suitable cutting and deburring tools on hand. The Barrow GJSGW silicone bending cord is available separately.

FAQ

What size acrylic or PETG tube fits this mold?

Use rigid tubing with an outside diameter of 12, 14, or 16 mm. PMMA is acrylic.

What bend shapes can I make?

Barrow shows setups for a single corner, a parallel offset, and a U-shaped return. Move the guide arms to set up the bend for your route.

How do I size the silicone bending insert?

Choose an insert that fits the inside diameter of the tube. It supports the tube wall from the inside while you bend it.

Where do I aim the heat gun?

Heat the section of tubing you want to bend and keep the hot air away from the ABS guides.

Notes
  • Barrow may update the tool’s appearance or construction without notice.