ASRock Radeon RX 9070 XT Taichi 16GB OC GPU Water Block, Barrow BS-AMD9070XT-PA

Barrow · BS-AMD9070XT-PA

Full-cover water cooling for the RX 9070 XT Taichi

The Barrow BS-AMD9070XT-PA is a full-cover GPU water block for the ASRock Radeon RX 9070 XT Taichi 16GB OC. It replaces the stock air cooler so the GPU core, memory, and power delivery components can be cooled by a custom liquid loop. The block has G1/4 ports and comes with an aluminum backplate.

Fits
ASRock Taichi 16GB OC
Ports
G1/4
Lighting
5V 3-pin ARGB
Backplate
Black or white

Compatibility

Barrow lists one supported graphics card.

  • ✓ASRock Radeon RX 9070 XT Taichi 16GB OC (RX9070XT TC 16GO)

Before ordering, verify the exact card model, PCB layout, and mounting-hole pattern.

ASRock’s Taichi 16GB OC with its factory cooler.

Design Highlights

Barrow’s schematic of the cooling contact areas.

Cooling across the GPU and power delivery area

The cold plate spans the GPU core, memory, and power delivery area, including the MOSFETs, chokes, and tantalum capacitors. Heat moves from those contact areas into the block and then into the coolant.

43 microchannels over the GPU

Barrow specifies 10 mm copper stock for the CNC-machined cold plate. The 5+3 groove pattern uses 0.5 mm grooves with 0.3 mm spacing to increase the surface area in contact with coolant.

Addressable lighting through clear acrylic

The clear acrylic top exposes the coolant path and the built-in LRC 2.0 lighting. For motherboard control, use the included adapter cable to connect to a 5V 3-pin ARGB header.

Key Specifications

ModelBS-AMD9070XT-PA
Cold plateCopper cold plate
Core designThree-layer cooling structure
TopClear acrylic
BackplatePassive aluminum alloy
Backplate finishBlack or white
Block dimensions209 × 123 × 24 mm
I/O bracket designDual slot
Port threadG1/4
LightingLRC 2.0 · 5V 3-pin ARGB via included adapter cable

Barrow’s block drawing. All dimensions shown in millimeters.

Which Version Do I Need?

Select the block by the exact graphics card model.

Barrow BS-AMD9070XT-PATHIS PAGE
For the ASRock Taichi 16GB OC. Choose a black or white aluminum backplate.
An alternative full-cover block for the same ASRock Taichi 16GB OC, supplied with its own backplate.
Choose this model for the GIGABYTE Radeon RX 9070 XT GAMING OC 16G.

What's in the Box

1 × GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set5V 3-pin ARGB motherboard adapter cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

White and black backplate options.

Installation & Use

1
Remove the stock backplate and air cooler. Disconnect the cooler’s fan cable and clean the old thermal material off the GPU and contact areas.
2
Cut and place the thermal pads according to the diagram. Apply your own thermal paste to the GPU die.
3
Align the block and backplate with the card’s mounting holes and tighten the mounting screws evenly.
4
Connect the loop with G1/4 tube fittings, seal the unused ports with the stop plugs, and leak-test the loop before powering the card.

For a new loop, have a pump, reservoir, radiator, tubing, matching G1/4 tube fittings, and PC coolant ready.

Barrow’s pad placement guide for this model. ① 1.2 mm · ② 0.5 mm · ③ 1.0 mm.

FAQ

Is this an AIO cooler for the RX 9070 XT?

It is a GPU water block for a custom loop. Use it with a pump, reservoir, radiator, tubing, fittings, and coolant.

How do I tell if this fits my RX 9070 XT?

Look for ASRock model RX9070XT TC 16GO, sold as the Radeon RX 9070 XT Taichi 16GB OC. Verify your PCB against Barrow’s Taichi layout before ordering.

What fittings should I buy?

Use G1/4 tube fittings that match your tubing. The two included stop plugs close unused ports.

Does the backplate connect to the coolant loop?

The included aluminum backplate is passive. Connect the coolant lines to the water block terminal.

Which motherboard header controls the lighting?

Connect the lighting through the included adapter cable to a 5V 3-pin ARGB header. Keep it away from 12V 4-pin RGB headers.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.