Gigabyte RX 7900 XTX Gaming OC Water Block with Backplate | Bykski A-GV7900XTXGMOC-X

Bykski · A-GV7900XTXGMOC-X

Full-cover water block for the Gigabyte RX 7900 XTX Gaming OC

The Bykski A-GV7900XTXGMOC-X replaces the stock cooler on the Gigabyte Radeon RX 7900 XTX Gaming OC 24G. Its T2 copper cold plate cools the GPU core, memory, and voltage regulators in a custom liquid cooling loop. It comes with a black aluminum backplate and 5V addressable RGB lighting.

Fits
Gigabyte RX 7900 XTX Gaming OC 24G
Ports
G1/4
Lighting
5V 3-pin ARGB
Backplate
Black aluminum

Compatibility

Match your card to the Gaming OC board shown here.

  • ✓Gigabyte Radeon RX 7900 XTX GAMING OC 24G (GV-R79XTXGAMING OC-24GD)

Before ordering, confirm your exact card model and PCB revision, then compare the full board layout and mounting holes with the photo.

Gigabyte Radeon RX 7900 XTX Gaming OC 24G bare PCB. Photo by HKEPC.

Design Highlights

One cold plate for the GPU, memory, and VRM

The T2 copper cold plate uses a jet microchannel array with 0.5 mm gaps. The transparent acrylic top lets you see the coolant channels.

5V addressable lighting

Use the ARGB adapter cable to connect the lighting to a 5V 3-pin motherboard header. A compatible 5V controller can also drive the strip.

Key Specifications

ModelA-GV7900XTXGMOC-X
Cooling coverageGPU core, memory, and voltage regulators
Cold plateT2 copper
TopClear acrylic
BackplateBlack aluminum, outside the coolant path
Port threadG1/4 inlet and outlet
Microchannel gap0.5 mm
Block (L × W × T)292.07 × 147.96 × 23.05 mm
Backplate (L × W × T)292.07 × 116.81 × 6.03 mm
Lighting5V 3-pin addressable RGB (RBW)

Which Version Do I Need?

Check the exact board before choosing between these two blocks.

Bykski A-GV7900XTXGMOC-XTHIS PAGE
Choose this block for the Gigabyte Radeon RX 7900 XTX Gaming OC 24G PCB shown above.
Choose this model for the AMD Radeon RX 7900 XT reference PCB.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB light strip1 × ARGB adapter cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the PC and remove the graphics card. Take off the stock cooler and clean away the old pads and paste.
2
Cut the included thermal pads to size and place them on the memory and power components marked in the diagram. Apply a thin layer of your own thermal paste to the GPU die.
3
Align the water block and backplate with the PCB mounting holes. Fit the supplied hardware and tighten the screws gradually and evenly.
4
Attach G1/4 fittings at the marked inlet and outlet and plug unused openings. Connect the tubing and leak-test the loop before powering the card.

You also need a pump, radiator, G1/4 fittings, tubing, and coolant.

Apply pads to the red-outlined locations and paste to the GPU die in the center.

FAQ

How do I check whether this block fits my RX 7900 XTX?

Look for Gigabyte model GV-R79XTXGAMING OC-24GD and match the PCB and mounting holes to the photo above.

Can I use this as a standalone GPU cooler?

It’s a component for a custom loop. You’ll also need a pump, radiator, G1/4 fittings, tubing, and coolant.

Which RGB header should I use?

Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the light strip.

Where do the thermal pads go?

Cut the included pads to fit and place them on the memory and power components marked in the installation diagram.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.