MSI RX 7900 XTX Gaming Trio Classic 24G Water Block with Backplate, Bykski A-MS7900XTXTRIO-X

Bykski · A-MS7900XTXTRIO-X

Full-cover GPU water block for the MSI RX 7900 XTX Gaming Trio Classic 24G

The Bykski A-MS7900XTXTRIO-X replaces the stock air cooler on the MSI Radeon RX 7900 XTX Gaming Trio Classic 24G so the card can run in a custom liquid cooling loop. The nickel-plated copper cold plate draws heat from the GPU core, memory, and voltage regulators. An aluminum backplate mounts behind the card.

Fits
MSI Gaming Trio Classic 24G PCB
Cold plate
Nickel-plated T2 copper
Ports
G1/4 inlet and outlet
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists one MSI custom PCB for this block.

  • ✓MSI Radeon RX 7900 XTX Gaming Trio Classic 24G

MSI also makes an RX 7900 XT Gaming Trio Classic 20G. Check for XTX and 24G on your exact model, then compare your card’s PCB layout with the drawing in Installation & Use before ordering.

MSI’s photo of the compatible card with its original cooler.

Design Highlights

Cooling for the GPU, memory, and VRM

Contact areas on the cold plate transfer heat from the GPU core, memory, and voltage regulator modules (VRM) into the coolant.

G1/4 loop connections

The clear acrylic top exposes the coolant channels. Follow the inlet and outlet markings when you connect the block to your loop.

5V addressable lighting

Use the lighting sync cable with a 5V 3-pin ARGB motherboard header, or use a compatible 5V controller. A 12V 4-pin RGB header can damage the light strip.

Key Specifications

ModelA-MS7900XTXTRIO-X
Cold plateNickel-plated T2 copper
TopClear acrylic
BackplateBlack aluminum backplate, outside the coolant path
Port threadG1/4
Lighting5V 3-pin ARGB (RBW)
Water block (L × W × T)299.96 × 165.58 × 23.25 mm
Backplate (L × W × T)299.96 × 135.58 × 5.99 mm

Bykski drawing. Backplate above and water block below. Dimensions are in millimeters.

Which Version Do I Need?

Start with the full model name on your RX 7900 XTX. Bykski makes different blocks for MSI Gaming Trio Classic and Gigabyte Gaming OC boards.

Bykski A-MS7900XTXTRIO-XTHIS PAGE
Choose this block for the listed MSI Gaming Trio Classic 24G PCB.
Check this block’s PCB listing if you have the Gigabyte Radeon RX 7900 XTX Gaming OC.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB light strip1 × lighting sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski image of the included aluminum backplate.

Installation & Use

1
Shut down and disconnect power, remove the card, and take off its stock cooler and backplate. Clean the old thermal paste and pad residue from the GPU and surrounding components.
2
Match the mounting holes to the block. Cut the supplied thermal pads to fit the marked memory and MOSFET locations. Peel off the protective film, then apply a thin layer of your own thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Tighten the mounting screws a little at a time in a cross pattern, then secure the remaining backplate screws.
4
Attach the tubing with G1/4 fittings and close any unused ports with the supplied stop plugs.
5
Leak-test the filled loop while the graphics card is unpowered. Power the card once the loop passes the leak test.

You also need a pump, reservoir, radiator with fans, G1/4 fittings, tubing, coolant, and your own thermal paste.

Bykski’s pad placement drawing. The long gray strips mark the pad locations. The center square marks the GPU die.

FAQ

Does this fit the RX 7900 XT Gaming Trio Classic 20G?

Bykski’s fit list specifies the MSI Radeon RX 7900 XTX Gaming Trio Classic 24G PCB. Check the full model name and board layout before ordering.

What is the cold plate made of?

The cold plate is nickel-plated T2 copper. The top is clear acrylic, and the aluminum backplate stays outside the coolant path.

What else do I need to water-cool the card?

Use a custom loop with a pump, reservoir, radiator and fans, coolant, tubing, and G1/4 fittings that match your tubing.

Which RGB header do I use?

Use a 5V 3-pin ARGB header or a compatible 5V controller. Connecting the 5V strip to a 12V 4-pin RGB header can damage it.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.