Bykski · A-PC7900XTXDEVIL-X
Full-cover water block for the PowerColor Red Devil RX 7900 XTX
The Bykski A-PC7900XTXDEVIL-X is a full-cover water block for the PowerColor Red Devil Radeon RX 7900 XTX 24GB with Bykski’s specified PCB layout and three 8-pin PCIe power connectors. It replaces the stock cooler and connects to a custom loop to cool the GPU core, memory, and voltage regulators. It includes an aluminum backplate and 5V addressable RGB lighting.
Fits
Red Devil RX 7900 XTX 24GB
Compatibility
Bykski lists the following Red Devil PCB layout.
- ✓PowerColor Red Devil Radeon RX 7900 XTX 24GB (RX7900XTX 24G-E/OC), with three 8-pin PCIe power connectors
The PowerColor Hellhound (RX7900XTX 24G-L/OC) and PowerColor reference card (RX7900XTX 24G) each have two 8-pin power connectors.
Before ordering, confirm the model on your card and compare the full PCB, including the mounting holes and component layout, with Bykski’s bare PCB reference in the sixth image of the product gallery.
PowerColor Red Devil RX 7900 XTX 24GB with its original cooler.
Design Highlights
Bykski’s coolant flow illustration.
Full-cover cooling
The cold plate has contact areas for the GPU die, memory, and voltage regulators. Coolant carries heat from these areas to the radiator in your loop.
Jet microchannels over the GPU
Coolant passes through the fine channels in the cold plate above the GPU core. The clear acrylic top leaves the machined flow path visible.
5V addressable RGB
The included RBW light strip illuminates the clear top. Connect it to a 5V 3-pin ARGB header using the lighting sync cable.
Key Specifications
| Model | A-PC7900XTXDEVIL-X |
|---|
| Cold plate | Copper |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Black aluminum |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Water block (L × W × T) | 285.29 × 157.46 × 23.15 mm |
|---|
| Backplate (L × W × T) | 284.89 × 127.46 × 6.00 mm |
|---|
| Lighting | 5V 3-pin ARGB (RBW) |
|---|
Bykski dimensions in millimeters. Water block above, backplate below.
Which Version Do I Need?
Match the water block to the card maker and the specific RX 7900 XTX model on your label.
A-PC7900XTXDEVIL-XTHIS PAGE
Choose this block for the matching PowerColor Red Devil RX 7900 XTX 24GB PCB.
Check this block for the ASRock Radeon RX 7900 XTX Taichi 24GB OC.
Check this block for the Sapphire Radeon RX 7900 XTX Nitro+.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware setThermal pad set1 × 5V ARGB light strip1 × lighting sync cable
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
The included backplate mounts behind the graphics card PCB.
Installation & Use
1Power off the system and remove the graphics card. Remove the stock cooler and clean away the old thermal materials.
2Cut the pads to fit the memory and voltage regulator locations shown in Bykski’s guide. Apply your own thermal paste to the GPU die.
3Align the water block with the PCB holes and secure the block and backplate using the mounting hardware. If the holes fail to line up, stop and recheck the PCB.
4Connect the loop to the marked inlet and outlet with G1/4 fittings. Use the stop plugs to seal the unused ports.
5To connect the lighting, align the cable arrow with the +5V pin on a 3-pin ARGB header.
6Fill and leak-test the loop with the graphics card unpowered.
You also need a pump and reservoir, a radiator, coolant, tubing, and G1/4 fittings sized for that tubing.
1 Water block · 2 Thermal pads · 3 Graphics card PCB · 4 Block fasteners · 5 Backplate · 6 Backplate screws.
FAQ
Is this the water block used on the RX 7900 XTX Liquid Devil?
PowerColor ships the Liquid Devil with a factory-fitted EK water block. Bykski lists this block for the Red Devil PCB in its compatibility guide.
How long is the water block?
The block is 285.29 mm long, 157.46 mm wide, and 23.15 mm thick. Use the dimension drawing when planning clearance.
What fittings should I use?
The inlet and outlet take G1/4 fittings. Choose fittings that match the type and diameter of your tubing.
Which motherboard header powers the lighting?
Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the LEDs.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.