Bykski · A-PC9070XT-X
Full-cover water block for PowerColor RX 9070 XT
The Bykski A-PC9070XT-X is a full-cover GPU water block for supported PowerColor Radeon RX 9070 XT boards. It replaces the stock cooler and transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop. The block includes a black aluminum backplate.
Fits
PowerColor Hellhound / Reaper RX 9070 XT
Lighting
5V ARGB (Bykski RBW)
Compatibility
Match your PowerColor card to one of these models.
- ✓PowerColor Hellhound AMD Radeon RX 9070 XT 16GB GDDR6 (RX9070XT 16G-L/OC)
- ✓PowerColor Reaper AMD Radeon RX 9070 XT 16GB GDDR6 (RX9070XT 16G-A)
Before ordering, confirm the full model number and verify the PCB layout and mounting holes on your exact card.
PowerColor Hellhound RX 9070 XT bare PCB. Photo from Alphacool’s GPU configurator.
Design Highlights
Full-cover copper cold plate
The copper cold plate draws heat from the GPU core, memory, and voltage regulators. Coolant carries that heat to the radiator in your loop.
Jet microchannels
Coolant passes through the microchannels in the cold plate above the GPU core.
ARGB lighting through clear acrylic
The addressable LEDs light up the clear top. Use a matching 5V RBW controller, or use a compatible 5V RBW-to-ARGB adapter cable if the light’s plug differs from your motherboard’s 5V 3-pin ARGB header.
Key Specifications
| Manufacturer model | A-PC9070XT-X |
|---|
| Cold plate | T2 copper |
|---|
| Copper plate length | 127.52 mm |
|---|
| Top | Clear acrylic (PMMA) |
|---|
| Backplate | Black aluminum, passive |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Jet microchannels | 0.3 mm, up to 50 channels |
|---|
| Inlet and outlet thread | G1/4 |
|---|
| Water block (L × W × T) | 195.45 × 137.00 × 26.15 mm |
|---|
| Backplate (L × W × T) | 195.45 × 106.90 × 5.94 mm |
|---|
| Lighting standard | 5V addressable RGB (Bykski RBW) |
|---|
| Lighting connection | Matching 5V RBW controller, or a 5V 3-pin ARGB motherboard header with a compatible 5V RBW-to-ARGB adapter cable if the plugs differ. |
|---|
Water block above, backplate below. Dimensions are in millimeters.
Which Version Do I Need?
Start with the graphics card brand and model on your card’s label, then check the PCB.
Bykski A-PC9070XT-XTHIS PAGE
Choose this block for the PowerColor Hellhound or Reaper RX 9070 XT listed above.
Choose this version for the GIGABYTE Radeon RX 9070 XT GAMING OC 16G or RX 9070 GAMING OC 16G.
Choose this version for the ASUS TUF Gaming Radeon RX 9070 OC Edition 16GB (TUF-RX9070-O16G-GAMING).
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugsThermal pads and mounting hardware (washers, spring screws and backplate screws)
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
1 Water block · 2 Thermal pads · 3 Your graphics card PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws
Installation & Use
1Power off the PC, remove the graphics card, and remove its stock cooler. Clean the old thermal material off the GPU and the parts it contacted.
2Match the block to the PCB. Place the supplied thermal pads on the indicated memory and VRM contact points, and apply a thin layer of your own thermal paste to the GPU die.
3Align the block and PCB. Install the washers and short spring screws as shown in the assembly drawing. Tighten gradually and evenly, then attach the backplate with its longer screws.
4Connect the inlet and outlet to your loop with G1/4 fittings and seal the unused openings with the stop plugs. For lighting, use a matching 5V RBW controller or a compatible 5V RBW-to-ARGB adapter cable if the plug differs from your motherboard’s 5V 3-pin ARGB header.
5Fill and leak-test the loop before powering the graphics card.
For the rest of the loop, you’ll need a pump, radiator, tubing, G1/4 fittings that match the tubing, and coolant.
The shaded areas around the GPU mark memory and VRM pad locations. Apply paste to the GPU die at the center.
FAQ
Does this fit the PowerColor Reaper RX 9070 XT?
Yes. Check for model RX9070XT 16G-A and verify your card’s PCB layout before ordering.
Can I use it as an AIO cooler?
This block is a component for a custom loop. It needs a pump, radiator, tubing, fittings, and coolant.
What fittings does the block use?
Use G1/4 loop fittings sized to your tubing. Use the included stop plugs to seal the unused openings.
How do I connect the lighting?
Use a matching 5V RBW controller. If the light’s plug differs from your motherboard’s 5V 3-pin ARGB header, use a compatible 5V RBW-to-ARGB adapter cable. A 12V 4-pin RGB header can damage the LEDs.
Does the water block come with a backplate?
Yes. The included black aluminum backplate mounts behind the PCB. Coolant flows through the front block.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.