RX 6700 XT Water Block - Bykski A-RX6700XT-X-V2 Full Cover with Backplate

Bykski · A-RX6700XT-X-V2

Full-cover water block for select Radeon RX 6700 XT cards

The Bykski A-RX6700XT-X-V2 is a full-cover water block for the AMD Radeon RX 6700 XT reference PCB and the specific partner boards listed below. It replaces the stock cooler and transfers heat from the GPU core, memory, and voltage regulators to a custom liquid cooling loop. The kit includes a black aluminum backplate.

Fits
RX 6700 XT reference and listed partner PCBs
Cold plate
Nickel-plated T2 copper
Lighting
5V 3-pin RBW
Backplate
Black aluminum

Compatibility

This block fits the following RX 6700 XT PCB layouts.

  • ✓AMD Radeon RX 6700 XT (reference PCB)
  • ✓Sapphire NITRO+ Radeon RX 6700 XT (Super Platinum)
  • ✓Sapphire PULSE Radeon RX 6700 XT (Platinum Edition)
  • ✓XFX Radeon RX 6700 XT (Overseas Edition / Global Version)
  • ✓XFX Radeon RX 6700 XT Snow Wolf
  • ✓Dataland Radeon RX 6700 XT God of War

For the AMD reference card, use the photo to compare the bare PCB. For partner cards, confirm the full card part number, PCB revision, and mounting-hole layout for your specific model. Confirm unlisted versions before ordering.

Bare PCB of the AMD Radeon RX 6700 XT reference card.

Design Highlights

Contact across the board

The nickel-plated T2 copper cold plate contacts the GPU core and reaches the memory and voltage regulator modules through thermal pads.

Bykski’s illustration of the coolant path.

Microchannels over the GPU core

Coolant crosses the microchannel array above the GPU core. Bykski specifies 0.3 mm jet microchannels and up to 44 channels.

Black aluminum backplate

The included backplate mounts behind the PCB, outside the coolant path.

Key Specifications

ModelBykski A-RX6700XT-X-V2
Cold plateNickel-plated T2 copper
TopClear acrylic
BackplateBlack aluminum
Lighting5V 3-pin addressable RGB (RBW)
Block (L × W × T)241.14 × 126.07 × 23.45 mm
Backplate (L × W × T)241.15 × 95.99 × 6.00 mm

Bykski’s dimension drawing with the block above the backplate. All measurements are in millimeters.

What's in the Box

1 × full-cover GPU water block1 × black aluminum backplateThermal pad setMounting hardware set2× G1/4 stop plugs5V 3-pin ARGB motherboard adapter cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system. Remove the graphics card, take off the stock cooler, and clean old paste and pad residue from the GPU, memory, and power components.
2
Cut the thermal pads to cover the memory and power components where they meet the block. Apply a thin layer of your own thermal paste to the GPU die.
3
Align the block with the PCB mounting holes. Place the gaskets at the points shown in the diagram, then secure the block and backplate with the corresponding screws. Tighten gradually and evenly.
4
Connect the inlet and outlet to the loop with fittings that match the block and tubing. Seal any unused ports.
5
Use a compatible 5V RBW controller, or connect the lighting to a 5V 3-pin ARGB motherboard header with the included adapter cable.
6
Fill the loop and power only the pump for leak testing. Keep the graphics card and other components unpowered until the loop passes the test.

You also need a pump, radiator, tubing, matching fittings, and coolant.

1 water block · 2 thermal pads · 3 your graphics card PCB · 4 gaskets · 5 spring screws · 6 mounting screws · 7 backplate · 8 backplate screws

FAQ

Will this water block fit my AMD Radeon RX 6700 XT?

It fits the AMD reference PCB and the partner boards listed above. Check your full card part number and PCB revision before ordering.

Which Sapphire RX 6700 XT cards fit?

Bykski lists the Sapphire NITRO+ (Super Platinum) and PULSE (Platinum Edition) layouts. Confirm your exact part number and PCB revision before ordering.

How do I connect the RBW lighting?

Use a compatible 5V RBW controller. For motherboard sync, use the included adapter cable to connect the lighting to a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the lighting.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.