Bykski · A-SP6900XTSE-X
Full-cover GPU water block for select Sapphire Radeon cards
The Bykski A-SP6900XTSE-X is a full-cover GPU water block for the Sapphire NITRO+ Radeon RX 6900 XT Special Edition (11308-03-20G) and the other Sapphire boards listed below. It replaces the factory cooler and transfers heat from the GPU core, memory, and voltage regulators to a custom liquid cooling loop. An aluminum backplate is included.
Fits
Sapphire RX 6900 XT NITRO+ SE (11308-03-20G)
Compatibility
Match your Sapphire card to one of these exact models.
- ✓Sapphire NITRO+ Radeon RX 6900 XT Special Edition (11308-03-20G)
- ✓Sapphire TOXIC Radeon RX 6900 XT Extreme Edition (11308-08-20G)
- ✓Sapphire NITRO+ Radeon RX 6950 XT PURE (11317-04-20G)
- ✓Sapphire NITRO+ Radeon RX 6950 XT (11317-02-20G)
Before ordering, verify your card’s full part number and PCB layout, including its mounting holes and component positions.
Sapphire’s Radeon RX 6900 XT NITRO+ Special Edition (11308-03-20G) with the factory cooler installed.
Design Highlights
Visible coolant path
The clear acrylic top lets you see the coolant channels and the 0.5 mm jet microchannel section. The terminal connects to your loop through G1/4 ports.
Contact across the GPU, memory, and VRM
The T2 copper cold plate has raised contact areas for the GPU and the surrounding components. Use the pad layout for your mounting kit to line up the memory and VRM contact areas.
5V addressable lighting
Both configurations include an ARGB adapter cable for syncing the lighting through a 5V 3-pin motherboard header. Choose the optional lighting controller to control the LEDs without motherboard sync.
Key Specifications
| Model | A-SP6900XTSE-X |
|---|
| Cold plate | T2 copper |
|---|
| Top | Clear acrylic |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Microchannels | 0.5 mm jet microchannel gap |
|---|
| Backplate | Black aluminum, passive |
|---|
| Port thread | G1/4 |
|---|
| Lighting | 5V 3-pin addressable RGB (RBW) |
|---|
| Block (L × W × T) | 259.96 × 148.08 × 23.49 mm |
|---|
| Backplate (L × W × T) | 260.05 × 118.17 × 6 mm |
|---|
Which Version Do I Need?
RX 6900 XT cards use different board layouts. Use the graphics card’s full model name and PCB to choose a block.
Bykski A-SP6900XTSE-XTHIS PAGE
Choose this block for one of the four Sapphire models listed above.
Check this model if you have an AMD reference Radeon RX 6900 XT.
Check this model for the PowerColor Red Devil RX 6900 XT (AXRX 6900XT 16GBD6-3DHE/OC).
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 mounting hardware set1 thermal pad setARGB adapter cable for a 5V 3-pin motherboard header
The controller bundle adds one lighting controller.
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Shut down and disconnect the PC. Remove the graphics card and its original cooler, then clean off the old paste and pads. Check the PCB and mounting hole alignment.
2Cut and apply the thermal pads at the memory and VRM contact areas shown in the mounting guide for your kit. Apply a thin layer of your own thermal paste to the GPU die.
3Align the PCB and block. Fit the washers and screws as shown in the mounting guide, tighten the mounting screws gradually in a cross pattern, then secure the backplate.
4Connect the loop to the block’s inlet and outlet with G1/4 fittings. Seal unused openings with the supplied port plugs.
5Fill and bleed the loop and check the fittings and plugs for leaks with only the pump powered. Power the graphics card after the loop passes the leak test.
You also need a pump and reservoir, a radiator with fans, G1/4 tube fittings matched to your tubing, coolant, and your own thermal paste.
FAQ
Will this water block fit my RX 6900 XT?
Check the exact card model and part number in the compatibility list, then compare the full PCB layout before ordering.
Which Sapphire RX 6950 XT cards fit?
The listed boards are the NITRO+ PURE (11317-04-20G) and the NITRO+ (11317-02-20G). Verify the PCB on your card before ordering.
Can I connect the lighting to a 12V RGB header?
Use the included ARGB adapter cable with a 5V 3-pin motherboard header, or use the optional 5V lighting controller. Connecting the LEDs to a 12V 4-pin RGB header can damage them.
What fittings do I need?
Use G1/4 loop fittings that match the tubing you plan to use. The included plugs seal the openings you leave unused.
Notes- All products are covered by our return policy.
- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.