ASUS RTX 4090 AIO Liquid Cooler (TUF Gaming OG / ROG Strix LC), Bykski B-FRD-AS4090TUFOG

Bykski · B-FRD-AS4090TUFOG

360 mm AIO liquid cooler for ASUS RTX 4090 OG and Strix LC

The Bykski B-FRD-AS4090TUFOG is an all-in-one liquid cooler for select ASUS graphics cards, including the TUF Gaming GeForce RTX 4090 24GB OG. It replaces the stock cooler with a full-cover block that carries heat from the GPU, memory, and power stages to a case-mounted radiator. The single-card 360 mm kit described here includes an inline pump and three radiator fans.

Fits
ASUS TUF RTX 4090 OG, Strix LC RTX 4090, and TUF RTX 4070 Ti SUPER OG
Radiator
360 mm aluminum
Cold plate
Nickel-plated T2 copper
Pump
Inline

Compatibility

Bykski lists these ASUS graphics cards for this cooler.

  • ✓ASUS TUF Gaming GeForce RTX 4090 24GB OG (TUF-RTX4090-24G-OG-GAMING)
  • ✓ASUS ROG Strix LC GeForce RTX 4090 24GB (ROG-STRIX-LC-RTX4090-24G-GAMING)
  • ✓ASUS TUF Gaming GeForce RTX 4070 Ti SUPER 16GB OG OC Edition (TUF-RTX4070TIS-O16G-OG-GAMING)

Before ordering, check the exact model number on your card against the list. Use the TUF RTX 4090 OG photo as a PCB reference, then verify the mounting holes and component contact areas on your own card.

ASUS TUF Gaming GeForce RTX 4090 OG bare PCB. Image from ASUS.

Design Highlights

A radiator and pump in one loop

Braided tubing connects the GPU block to the radiator, with the pump mounted inline. Three 120 mm fans move air through the radiator.

Copper contact plate across the board

The nickel-plated T2 copper plate draws heat from the GPU core, memory, and power stages. Bykski rates the copper base material at 401 W/(m·K).

0.3 mm jet microchannels

The cold plate has up to 44 narrow coolant channels that increase the contact area between the liquid and the copper.

Key Specifications

Single-card SKUB-FRD-AS4090TUFOG-360
Cold plateT2 copper with electroless nickel plating
GPU block (L × W × T)222.30 × 119.58 × 16.60 mm
Radiator360 mm aluminum, 396 mm overall length, 12 coolant channels
Radiator fans3 × 120 mm
Inline pump7,000 RPM, 450 L/h, 7 m head
TubingBraided
Thermal pads1.5 mm

Bykski’s GPU block dimensions in millimeters.

Which Version Do I Need?

Start with the model number on your card. Look for the OG suffix on the TUF RTX 4090 or the LC designation on the ROG Strix RTX 4090.

B-FRD-AS4090TUFOGTHIS PAGE
Choose this AIO for a board in the compatibility list. The specifications and installation steps here cover the single-card 360 mm configuration.
Check this AIO if you have the standard ASUS TUF Gaming RTX 4090 or ROG Strix RTX 4090. It uses a block for a different PCB layout.

What’s in the Box — Single-Card 360 mm Kit

1 × full-cover GPU block with backplate1 × 360 mm radiator with inline pump and tubing3 × 120 mm radiator fans1.5 mm thermal padsMounting hardware

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Shut down the PC, disconnect power, and remove the graphics card and its stock cooler.
2
Clean off the old thermal material. Trim the pads to the memory and power-stage contact areas shown in the installation diagram, then apply your own GPU thermal paste to the GPU die.
3
Line up the block, PCB, and backplate with the mounting holes. Fit the spacers and fasten the assembly with the mounting hardware.
4
Mount the radiator and fans in the case. Leave room to route the tubing and position the inline pump without kinking the tubing.
5
Connect the pump and fans to the appropriate power headers for their plugs. Check that the pump and fans run and inspect the connections before putting the GPU under load.

You also need your own GPU thermal paste, a case with a 360 mm radiator mount, and suitable power connections for the pump and fans.

Bykski’s placement diagram. Shaded strips mark the pads. The syringe points to the GPU die.

FAQ

Which ASUS RTX 4090 should I check for this AIO?

Look for the TUF Gaming 24GB OG or ROG Strix LC 24GB model number in the compatibility list. Match your PCB to the reference before you order.

Do I need a separate pump or a custom loop?

The single-card 360 mm kit includes the pump, tubing, radiator, and GPU block in one assembly.

Will the 360 mm radiator fit my case?

Check for a 360 mm radiator mount with room for the radiator’s 396 mm overall length. Allow additional depth for the fans and space to route the tubing to the GPU.

Where do the thermal pads go?

Use the 1.5 mm pads on the memory and power-stage contact areas shown in the installation diagram. Apply your own GPU thermal paste to the GPU die.

Notes
  • Bykski lists speed, flow, and head as separate specifications for the pump.