Gigabyte RTX 4090 AIO Liquid Cooler, 360 mm, for WINDFORCE V2 24G & TURBO 24G | Bykski B-FRD-GV4090WF

Bykski · B-FRD-GV4090WF

360 mm liquid cooling for select Gigabyte RTX 4090 cards

The Bykski B-FRD-GV4090WF is a 360 mm all-in-one liquid cooler for compatible Gigabyte GeForce RTX 4090 cards. On the standard kit, a full-cover copper block replaces the stock cooler and draws heat from the GPU, memory, and power stages. An inline pump moves coolant from the block to the case-mounted radiator.

Fits
Gigabyte RTX 4090 WINDFORCE V2 24G / TURBO 24G
Radiator
360 mm
Standard cold plate
Copper
Standard pump
Inline

Compatibility

Bykski lists these cards for the standard kit.

  • ✓Gigabyte GeForce RTX 4090 WINDFORCE V2 24G (GV-N4090WF3V2-24GD)
  • ✓Gigabyte GeForce RTX 4090 TURBO 24G

Not compatible:

  • ✗RTX 4090 cards with a different PCB layout

Before ordering, confirm your exact card model. Compare the mounting holes and component layout on your card with the bare PCB photo in the product gallery and the installation drawing here.

PCB layout (Bykski installation drawing)

Design Highlights — Standard 360 mm Kit

The pump sits in the tubing

The inline pump circulates coolant between the GPU block and the aluminum radiator. Three fans move air through the radiator, where heat leaves the loop.

The cold plate covers the GPU, memory, and power stages

The copper plate has raised contact areas for the GPU and the components around it. Bykski lists the copper base material at 401 W/(m·K).

Jet microchannels in the block

The block uses 0.3 mm jet microchannels to increase the surface area in contact with the coolant. Bykski specifies up to 44 channels.

Key Specifications — Standard 360 mm Kit

ModelB-FRD-GV4090WF-360
Block coverageGPU, memory, and power stages
Cold plateCopper
Block dimensions271.01 × 124.72 × 21.50 mm (length × height × thickness)
Radiator360 mm aluminum radiator
Radiator length396 mm end to end in Bykski’s 360 mm drawing
Radiator fans3 included, 120 mm each and 25 mm thick
Radiator thickness with fans63 mm (38 mm radiator + 25 mm fans)
Pump and tubingInline pump with braided tubing

GPU block dimensions (Bykski drawing)

Which Version Do I Need?

Check the full model name on the card label. Gigabyte lists the original WINDFORCE 24G and the WINDFORCE V2 24G as separate models.

B-FRD-GV4090WF-360
Select 360mm in Size and Black in Color for the single-card kit with one GPU block and one matching backplate. The radiator and fans together are 63 mm thick.
B-FRD-GV4090WF-360-H
Select 360mm Thick row(Dual Graphics Cards) in Size and Black in Color for the dual-card kit. It includes two GPU blocks, two matching backplates, mounting hardware for both blocks, and one 360 mm radiator with three 120 mm fans (25 mm thick each). The radiator and fans together are 63 mm thick.

What's in the Box — Standard 360 mm Kit

Factory-filled loop with 1 GPU block, pump, tubing, and 1 × 360 mm radiator3 × 120 mm radiator fans1 matching GPU backplateThermal padsMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Standard cooler layout (Bykski rendering)

Installation & Use — Standard 360 mm Kit

1
Power off the system, remove the graphics card, and take off the stock cooler. Clean off the old paste and pads.
2
Cut the thermal pads to fit the memory and MOSFET contact areas shown in Bykski's installation diagram. Apply thermal paste to the GPU die.
3
Line up the block with the PCB screw holes. Stop if the holes do not line up. Secure the block with the mounting hardware. Follow the kit instructions for fitting the backplate.
4
Mount the radiator and fans in a 360 mm case position. Allow room for the pump and route the tubing without sharp bends.
5
Before powering on, confirm the pump and fan connections using instructions for the B-FRD-GV4090WF-360. If you do not have those instructions, contact customer service. Check the tubing and connections before startup, then verify that the pump and fans run.

You also need a screwdriver, thermal paste for the GPU die, and a case with a 360 mm radiator mount.

FAQ

Do I need to connect the tubing or add coolant?

The GPU block, pump, and radiator come connected and filled with coolant at the factory. No initial fill is needed.

What should I measure for the standard kit?

Check for a 360 mm radiator mount with clearance for the 63 mm radiator and fan assembly. Before choosing the mount, check that the hoses can reach the GPU and that the inline pump has room. Current kits ship with the 38 mm radiator; total thickness with fans is 63 mm (older drawings may show 52 mm).

Which thermal pads go on the board?

Cut the thermal pads to fit the memory and MOSFET areas shown in Bykski's installation diagram. Use thermal paste on the GPU die.

Is the original WINDFORCE 24G the same fit as the V2?

Gigabyte lists them as separate cards. The Bykski compatibility table names the WINDFORCE V2 24G. Confirm your exact model and PCB layout before ordering.

What does this AIO replace on the RTX 4090 WINDFORCE V2?

The standard kit replaces the stock three-fan air cooler. Its full-cover block cools the GPU, memory, and power stages, and its inline pump circulates coolant to the radiator.

Notes
  • For any questions, please contact customer service.