Bykski · CP-NWD6-X-CT60

D6 pump and reservoir combo for custom PC water cooling

The Bykski CP-NWD6-X-CT60 combines a D6 pump and a clear tube reservoir for a custom PC water cooling loop. The reservoir holds coolant and lets you see the fill level, while the PWM-controlled pump circulates coolant through the loop. Connect it with G1/4 fittings and choose a reservoir length that fits your build.

Fits
G1/4 loop fittings
Max pump flow
720 L/h
Pump input
22 W
Reservoir lengths
60 / 100 / 150 / 200 mm

Use With

For custom PC liquid cooling loops.

  • ✓G1/4 loop fittings
  • ✓12 V power from a PSU’s 4-pin Molex peripheral connector
  • ✓A PWM header or controller for pump speed control
  • ✓For the RBW option, a 5 V 3-pin ARGB header or compatible controller

Use a matching ARGB adapter for a motherboard connection. Do not connect the RBW lighting lead to a 12 V 4-pin RGB header.

1–2 Pump power · 3 Tach feedback · 4 PWM speed control.

Design Highlights

Clear reservoir above the D6 pump

The PMMA acrylic tube lets you check the coolant level while filling and bleeding the loop. The D6 pump uses a ceramic shaft and an aluminum alloy outer housing.

Four reservoir lengths

Each cover option comes in 60, 100, 150, and 200 mm reservoir lengths. Measure your available space for the complete pump and reservoir assembly, with extra room to reach the fill port.

A choice of pump covers and lighting

Choose a black POM pump cover, a clear acrylic cover with RBW lighting, or a clear acrylic cover without lighting. The RBW option uses a separate 5 V 3-pin ARGB connection.

Key Specifications

ModelCP-NWD6-X-CT60
Pump coreCP-D6PB-X brushless DC centrifugal pump
Reservoir tubeClear PMMA acrylic
Pump coverClear acrylic or black POM
Pump housing diameter81 mm (black POM and 60/100 mm clear RBW)
Reservoir section lengths60 / 100 / 150 / 200 mm
Overall height, clear RBW147.7 mm (60 mm), 187.7 mm (100 mm)
Overall height, black POM136.7 / 176.7 / 226.7 / 276.7 mm, in order of reservoir length
Loop fitting threadG1/4
Maximum pump flow720 L/h
Pump speed1,800–4,800 RPM
Rated pump input12 V DC, 1.85 A, 22 W
Pump connections4-pin Molex power and separate PWM / tach lead
Lighting connection (RBW option)5 V 3-pin ARGB

Black POM version with a 60 mm reservoir. Dimensions in millimeters.

Which Version Do I Need?

Check the model number when comparing Bykski pump and reservoir combinations.

Bykski CP-NWD6-X-CT60THIS PAGE
Choose this if you need a complete D6 pump and reservoir assembly.
Choose the separate D6 pump core if you only need the motor.
Choose this separate pump and reservoir assembly if your build calls for a D5 pump.

What's in the Box

1 × D6 pump and reservoir assembly in the selected version

Installation & Use

1
Check the space for the full assembly and leave access to the fill port. Secure the assembly with suitable mounting hardware. Bykski shows its B-BKT-105 bracket used with ring clamps.
2
Connect the inlet and outlet to your loop with G1/4 fittings and tubing.
3
Connect pump power to the PSU’s Molex peripheral lead and the speed-control lead to a PWM header or controller. If you selected RBW, connect its lighting separately to a compatible 5 V ARGB connection.
4
Fill the reservoir before powering the pump. Top it up as air clears from the loop and keep the pump supplied with coolant.
5
Leak-test with only the pump powered. Power the rest of the PC once the loop is leak-free and the hardware is dry.

To complete the loop, you’ll also need G1/4 fittings, matching tubing, a radiator, water block and coolant.

Bykski’s ring-clamp and bracket mounting example.

FAQ

How much power does the D6 pump draw?

Bykski specifies 22 W of pump input power at 12 V DC and 1.85 A.

Does the PWM cable supply pump power?

Pump power comes from the PSU’s 4-pin Molex peripheral connector. The separate PWM lead controls speed and carries the tach signal.

Is the selected length the overall height?

The 60, 100, 150, and 200 mm options describe the reservoir section. Include the pump housing when measuring your mounting space.

Which version has addressable lighting?

Choose RBW for 5 V 3-pin ARGB lighting. The clear unlit option comes without lighting.

What fittings fit this combo?

Use G1/4 fittings that match the tubing in your custom loop.

Notes
  • Brand manufacturers reserves right to alter block design to expand compatibility.
  • Delivered item may not 100% match pictured item.
  • In case of upgrading to the appearance and structure, no further notice, the real object shall prevail.