D6 PWM Water Pump Motor – Bykski CP-D6PB-X, 12 V

$51.94 piece
items available
View Details
Bykski · CP-D6PB-X

D6 PWM water pump motor for custom PC loops

The Bykski CP-D6PB-X is a D6 PWM water pump motor for circulating coolant in a custom PC cooling loop. It requires a separate pump top or pump-reservoir housing that explicitly supports this model. A 12 V DC lead powers the motor, and a separate PWM connection handles speed control and feedback.

Pump format
D6 core
Rated voltage
12 V DC
Maximum flow
720 L/h
Speed control
PWM with tach feedback

Design Highlights

The manufacturer’s illustration highlights the impeller and shows its direction of rotation.

Brushless centrifugal drive

A brushless DC motor drives the impeller to circulate coolant. Bykski uses a ceramic bearing to support the rotor.

Separate pump core

The motor and impeller form a single core that seats in a matching pump top. Use the dimensions below to check clearance and confirm the exact pump model with the housing maker.

Key Specifications

ModelCP-D6PB-X
Pump typeD6 brushless DC centrifugal pump core
RotorPPE
BearingCeramic
ColorBlack
LightingUnlit
Pump core (diameter × height)65 × 55 mm
Pump weight260 g
Rated voltage12 V DC
Working voltage range8–20 V DC
Input power22 W
Rated current1.85 A
Maximum input current2.0 A
Power connector4-pin Molex
Control connectorSeparate 4-position PWM and tach feedback plug
PWM frequency1–100 kHz
PWM duty cycle10–100%
Maximum flow720 L/h
Manufacturer noise figure≤40 dBA at a horizontal distance of 1 m, with background noise ≤20 dB
Coolant types listed by BykskiEthylene glycol or propylene glycol
Coolant temperature0–70 °C
Ambient temperature−25 to 70 °C
Ambient humidityBelow 90% RH

Pump core dimensions in millimeters, shown from the side and end.

Which Version Do I Need?

Choose the pump core if you already have a confirmed housing. For a new build, compare complete pump assemblies by what they include.

Bykski CP-D6PB-XTHIS PAGE
D6 pump core for a pump top or pump-reservoir housing that explicitly supports this model.
Choose this D6 pump and reservoir combo if you want both in one assembly.
Choose this pump if you want a PMMA pump top and mounting system included.

What's in the Box

CP-D6PB-X pump core with power and control leads

Choose a compatible pump top or pump-reservoir housing separately.

Installation & Use

1
Confirm that your pump top or pump-reservoir housing supports CP-D6PB-X. Seat the core with the seal and fasteners specified by the housing maker.
2
Run tubing to the housing’s marked inlet and outlet. Match the fittings to the housing’s ports and your tubing.
3
Connect the 4-pin Molex lead to 12 V DC power and the separate PWM and tach lead to a compatible control header.
4
Fill the loop and make sure coolant reaches the pump before you apply power.
5
Power only the pump while you bleed air and check the loop for leaks. Once the loop passes the leak test, power on the rest of the PC.

Have the matching housing, seal, mounting hardware, fittings, tubing, and coolant ready.

Diagram callouts: 1 · +12 V power, 2 · power return, 3 · tach feedback, 4 · PWM speed control.

FAQ

What is the pump’s power draw?

Bykski lists 22 W input power and 1.85 A rated current at 12 V DC.

What happens with the PWM lead disconnected?

With 12 V power connected, the pump defaults to full speed when it receives no PWM signal.

Will my loop flow at 720 L/h?

Bykski lists a maximum flow of 720 L/h. Actual flow depends on the resistance in your loop.

What should I check before buying a pump top?

Confirm that the housing maker lists the CP-D6PB-X and follow its requirements for the seal, mounting hardware, and fittings.

Notes
  • Keep the pump out of direct sunlight and away from direct UV exposure.
  • Prime the pump with coolant before startup. Running it dry can damage it.