D5 Pump Reservoir Combo - Bykski CT-D5-180-X-V2, 350 mL, G1/4, PWM

Bykski · CT-D5-180-X-V2

D5 PWM pump and reservoir for custom PC water cooling

The Bykski CT-D5-180-X-V2 combines a D5 PWM pump and a 350 mL acrylic reservoir in one assembly. It circulates coolant in a custom PC water cooling loop with G1/4 fittings. The reservoir has a dedicated top fill port and clear windows so you can check the coolant level as you fill and bleed the loop.

Fits
G1/4 fittings
Reservoir
350 mL
Pump control
PWM
Rated voltage
12 V DC

Fittings & Mounting

  • ✓G1/4 threaded fittings for the loop connections
  • ✓120 mm chassis fan hole pattern with the Bykski B-BKT-105 bracket

Use in a loop without aluminum parts in contact with the coolant. Check case clearance for the assembly, fittings and access to the top fill port.

Design Highlights

Separate return and fill openings

Connect the tubing from your loop to the top return inlet. Use the other top opening to add coolant or let air escape while filling.

Aluminum outer housing

The pump sits below the acrylic reservoir in a black housing. The aluminum exterior stays outside the coolant path.

1–2 power, 3 speed feedback, 4 PWM control.

Separate power and speed control

The 4-pin Molex connector draws power from the PC power supply. The separate 4-pin PWM connector sends speed feedback and takes speed commands from a compatible header or controller.

Key Specifications

ModelCT-D5-180-X-V2
AssemblyBlack D5 PWM pump and reservoir
Reservoir350 mL clear acrylic (PMMA)
Housing materialsPOM and aluminum alloy
Body (H × W × D)266.6 × 75 × 75 mm
With bracket (W × D)116 × 94 mm as shown
Return, fill and outlet threadG1/4
Rated pump voltage12 V DC
Pump connections4-pin Molex power and separate 4-pin PWM

Bykski dimension drawing in millimeters, shown with the mounting bracket.

Which Version Do I Need?

CT-D5-180-X-V2 pump and reservoirTHIS PAGE
Choose this assembly when you want the pump and a 350 mL reservoir together.
Choose the option without a reservoir when you want to buy the pump separately.

What's in the Box

1 × assembled pump and reservoir

The D5 pump, aluminum pump housing and reservoir with top cap come assembled.

Installation & Use

1
Check the space needed for the assembly and tubing. To mount it at a 120 mm chassis fan position, secure it with a Bykski B-BKT-105 bracket.
2
Connect the loop return to the top inlet and route tubing from the pump outlet. Keep the fill port accessible.
3
Connect the Molex lead to the PC power supply and the PWM lead to a compatible motherboard header or controller.
4
Fill the reservoir and let coolant reach the pump before applying power. Top up the reservoir as air leaves the loop.
5
Check the connections for leaks with only the pump powered. Bykski recommends a 24-hour leak test before powering the rest of the system.

You also need G1/4 fittings, matching tubing, coolant, the water block or blocks for your hardware, a radiator and radiator fans.

Bykski chassis mounting illustration using the B-BKT-105 bracket.

FAQ

How much coolant does the reservoir hold?

The reservoir holds 350 mL.

Can I mount it at a 120 mm fan position?

Yes. Use a Bykski B-BKT-105 bracket and check your case clearance.

Where do I add coolant?

Use the separate fill port on the top cap. The other top port is the loop return inlet.

Which connector supplies pump power?

The 4-pin Molex connector supplies 12 V DC power. The separate 4-pin PWM connection is for speed control and feedback.

Notes
  • Keep coolant in the reservoir while bleeding the loop to avoid running the pump dry.